mirror of
https://0xacab.org/liberate/backupninja.git
synced 2024-11-08 20:02:32 +01:00
82 lines
3.5 KiB
Plaintext
82 lines
3.5 KiB
Plaintext
#
|
|
# this config file will save various reports of vital system information.
|
|
# by default, all the reports are saved in /var/backups.
|
|
#
|
|
# requires dpkg, debconf-utils, sfdisk, and hwinfo
|
|
#
|
|
# (1) a capture of the debconf package selection states. This file
|
|
# can be used to restore the answers to debconf questions for
|
|
# packages that you will be installing through (2) below. To
|
|
# do this, run: "debconf-set-selections < debconfsel.txt"
|
|
#
|
|
# (2) a list of all the packages installed and removed.
|
|
# this file can be used to restore the state of installed packages
|
|
# by running "dpkg --set-selections < dpkg-selections.txt and
|
|
# then run "apt-get -u dselect-upgrade". If you have the
|
|
# debconf-set-selections file from (1), you should restore those first.
|
|
#
|
|
# (3) the partition table of all disks.
|
|
# this partition table can be used to format another disk of
|
|
# the same size. this can be handy if using software raid and
|
|
# you have a disk go bad. just replace the disk and partition it
|
|
# by running "sfdisk /dev/sdb < partitions.sdb.txt"
|
|
# (MAKE SURE YOU PARTITION THE CORRECT DISK!!!)
|
|
#
|
|
# (4) hardware information.
|
|
# detailed information on most important aspects of the hardware.
|
|
#
|
|
# (5) the Luks header of every Luks block device, if option luksheaders
|
|
# is enabled.
|
|
# in case you (have to) scramble such a Luks header (for some time),
|
|
# and restore it later by running "dd if=luksheader.sda2.bin of=/dev/sda2"
|
|
# (MAKE SURE YOU PASS THE CORRECT DEVICE AS of= !!!)
|
|
#
|
|
# (6) LVM metadata for every detected volume group, if "lvm = yes"
|
|
#
|
|
# (7) a copy of each device's MBR, if "mbr = yes". A master boot record
|
|
# (MBR) is the 512-byte boot sector that is the first sector of a
|
|
# partitioned data storage device of a hard disk. To restore the MBR
|
|
# one could do something like: dd if=sda.mbr of=/dev/sda
|
|
# (MAKE SURE YOU PASS THE CORRECT DEVICE AS of= !!!)
|
|
# WARNING: Restoring the MBR with a mismatching partition table will
|
|
# make your data unreadable and nearly impossible to recover
|
|
#
|
|
# (8) a copy of the BIOS, if "bios = yes" and flashrom is installed
|
|
|
|
# here are the defaults, commented out:
|
|
|
|
# The output from the sys handler will be placed in $parentdir
|
|
# parentdir = /var/backups
|
|
# packages = yes
|
|
# packagesfile = /var/backups/dpkg-selections.txt
|
|
# selectionsfile = /var/backups/debconfsel.txt
|
|
|
|
# partitions = yes
|
|
# NOTE: the __star__ below will be replaced by the disks found on the
|
|
# system (e.g. partitions.sda.txt, partitions.sdb.txt). If you change
|
|
# the partitionsfile default below, be sure to include the __star__
|
|
# replacement in the filename, or you will get one file for only one disk,
|
|
# the others being written to the same file, and then overwritten by the next.
|
|
# partitionsfile = /var/backups/partitions.__star__.txt
|
|
# dosfdisk = yes
|
|
|
|
# hardware = yes
|
|
# hardwarefile = /var/backups/hardware.txt
|
|
# dohwinfo = yes
|
|
|
|
# luksheaders = no
|
|
# NOTE: the __star__ below will be replaced by the Luks partitions found on the
|
|
# system (e.g. luksheader.sda2.bin, luksheader.sdb3.bin). If you change
|
|
# the luksheadersfile default below, be sure to include the __star__
|
|
# replacement in the filename, or you will get one file for only one partition,
|
|
# the others being written to the same file, and then overwritten by the next.
|
|
# luksheadersfile = /var/backups/luksheader.__star__.bin
|
|
|
|
# lvm = no
|
|
|
|
# mbr = no
|
|
|
|
# note: to backup your BIOS, you need the program 'flashrom' installed, and your
|
|
# mainboard needs to be supported, see http://flashrom.org/Supported_hardware#Supported_mainboards
|
|
# bios = no
|