This folding happens as early as possible for performance reasons, and to make sure it isn't foiled by other transforms (e.g. forming FMAs).
llvm-svn: 163519
- CodeGenPrepare pass for identifying div/rem ops
- Backend specifies the type mapping using addBypassSlowDivType
- Enabled only for Intel Atom with O2 32-bit -> 8-bit
- Replace IDIV with instructions which test its value and use DIVB if the value
is positive and less than 256.
- In the case when the quotient and remainder of a divide are used a DIV
and a REM instruction will be present in the IR. In the non-Atom case
they are both lowered to IDIVs and CSE removes the redundant IDIV instruction,
using the quotient and remainder from the first IDIV. However,
due to this optimization CSE is not able to eliminate redundant
IDIV instructions because they are located in different basic blocks.
This is overcome by calculating both the quotient (DIV) and remainder (REM)
in each basic block that is inserted by the optimization and reusing the result
values when a subsequent DIV or REM instruction uses the same operands.
- Test cases check for the presents of the optimization when calculating
either the quotient, remainder, or both.
Patch by Tyler Nowicki!
llvm-svn: 163150
This reverts commit 5dd9e214fb92847e947f9edab170f9b4e52b908f.
Thanks to Duncan for explaining how this should have been done.
Conflicts:
test/CodeGen/X86/vec_select.ll
llvm-svn: 163064
Manage tied operands entirely internally to MachineInstr. This makes it
possible to change the representation of tied operands, as I will do
shortly.
The constraint that tied uses and defs must be in the same order was too
restrictive.
llvm-svn: 163021
because it does not support CMOV of vectors. To implement this efficientlyi, we broadcast the condition bit and use a sequence of NAND-OR
to select between the two operands. This is the same sequence we use for targets that don't have vector BLENDs (like SSE2).
rdar://12201387
llvm-svn: 162926
When there are multiple tied use-def pairs on an inline asm instruction,
the tied uses must appear in the same order as the defs.
It is possible to write an LLVM IR inline asm instruction that breaks
this constraint, but there is no reason for a front end to emit the
operands out of order.
The gnu inline asm syntax specifies tied operands as a single read/write
constraint "+r", so ouf of order operands are not possible.
llvm-svn: 162878
For normal instructions, isTied() is set automatically by addOperand(),
based on MCInstrDesc, but inline asm has tied operands outside the
descriptor.
llvm-svn: 162869
These extra flags are not required to properly order the atomic
load/store instructions. SelectionDAGBuilder chains atomics as if they
were volatile, and SelectionDAG::getAtomic() sets the isVolatile bit on
the memory operands of all atomic operations.
The volatile bit is enough to order atomic loads and stores during and
after SelectionDAG.
This means we set mayLoad on atomic_load, mayStore on atomic_store, and
mayLoad+mayStore on the remaining atomic read-modify-write operations.
llvm-svn: 162733
In SelectionDAGLegalize::ExpandLegalINT_TO_FP, expand INT_TO_FP nodes without
using any f64 operations if f64 is not a legal type.
Patch by Stefan Kristiansson.
llvm-svn: 162728
the case of multiple edges from one block to another.
A simple example is a switch statement with multiple values to the same
destination. The definition of an edge is modified from a pair of blocks to
a pair of PredBlock and an index into the successors.
Also set the weight correctly when building SelectionDAG from LLVM IR,
especially when converting a Switch.
IntegersSubsetMapping is updated to calculate the weight for each cluster.
llvm-svn: 162572
SelectionDAG's 'init' has not been called when the SelectionDAGBuilder is
constructed (in SelectionDAGISel's constructor), so this was previously always
initialized with 0.
llvm-svn: 162333
IR that hasn't been through SimplifyCFG can look like this:
br i1 %b, label %r, label %r
Make sure we don't create duplicate Machine CFG edges in this case.
Fix the machine code verifier to accept conditional branches with a
single CFG edge.
llvm-svn: 162230
The DAGCombiner tries to optimise a BUILD_VECTOR by checking if it
consists purely of get_vector_elts from one or two source vectors. If
so, it either makes a concat_vectors node or a shufflevector node.
However, it doesn't check the element type width of the underlying
vector, so if you have this sequence:
Node0: v4i16 = ...
Node1: i32 = extract_vector_elt Node0
Node2: i32 = extract_vector_elt Node0
Node3: v16i8 = BUILD_VECTOR Node1, Node2, ...
It will attempt to:
Node0: v4i16 = ...
NewNode1: v16i8 = concat_vectors Node0, ...
Where this is actually invalid because the element width is completely
different. This causes an assertion failure on DAG legalization stage.
Fix:
If output item type of BUILD_VECTOR differs from input item type.
Make concat_vectors based on input element type and then bitcast it to the output vector type. So the case described above will transformed to:
Node0: v4i16 = ...
NewNode1: v8i16 = concat_vectors Node0, ...
NewNode2: v16i8 = bitcast NewNode1
llvm-svn: 162195
This adds support for TargetIndex operands during isel. The meaning of
these (index, offset, flags) operands is entirely defined by the target.
llvm-svn: 161453