This patch adds builtin support for xvdivdp and xvdivsp, along with a
test case. Straightforward stuff.
There's a companion patch for Clang.
llvm-svn: 221983
This patch enables the vec_vsx_ld and vec_vsx_st intrinsics for
PowerPC, which provide programmer access to the lxvd2x, lxvw4x,
stxvd2x, and stxvw4x instructions.
New LLVM intrinsics are provided to represent these four instructions
in IntrinsicsPowerPC.td. These are patterned after the similar
intrinsics for lvx and stvx (Altivec). In PPCInstrVSX.td, these
intrinsics are tied to the code gen patterns, with additional patterns
to allow plain vanilla loads and stores to still generate these
instructions.
At -O1 and higher the intrinsics are immediately converted to loads
and stores in InstCombineCalls.cpp. This will open up more
optimization opportunities while still allowing the correct
instructions to be generated. (Similar code exists for aligned
Altivec loads and stores.)
The new intrinsics are added to the code that checks for consecutive
loads and stores in PPCISelLowering.cpp, as well as to
PPCTargetLowering::getTgtMemIntrinsic().
There's a new test to verify the correct instructions are generated.
The loads and stores tend to be reordered, so the test just counts
their number. It runs at -O2, as it's not very effective to test this
at -O0, when many unnecessary loads and stores are generated.
I ended up having to modify vsx-fma-m.ll. It turns out this test case
is slightly unreliable, but I don't know a good way to prevent
problems with it. The xvmaddmdp instructions read and write the same
register, which is one of the multiplicands. Commutativity allows
either to be chosen. If the FMAs are reordered differently than
expected by the test, the register assignment can be different as a
result. Hopefully this doesn't change often.
There is a companion patch for Clang.
llvm-svn: 221767
Now that we have initial support for VSX, we can begin adding
intrinsics for programmer access to VSX instructions. This patch adds
basic support for VSX intrinsics in general, and tests it by
implementing intrinsics for minimum and maximum for the vector double
data type.
The LLVM portion of this is quite straightforward. There is a
companion patch for Clang.
llvm-svn: 220988
A previous patch enabled SELECT_VSRC and SELECT_CC_VSRC for VSX to
handle <2 x double> cases. This patch adds SELECT_VSFRC and
SELECT_CC_VSFRC to allow use of all 64 vector-scalar registers for the
f64 type when VSX is enabled. The changes are analogous to those in
the previous patch. I've added a new variant to vsx.ll to test the
code generation.
(I also cleaned up a little formatting in PPCInstrVSX.td from the
previous patch.)
llvm-svn: 220395
The tests test/CodeGen/Generic/select-cc.ll and
test/CodeGen/PowerPC/select-cc.ll both fail with VSX enabled. The
problem is that the lowering logic for the SELECT and SELECT_CC
operations doesn't currently support the VSX registers. This patch
fixes that.
In lib/Target/PowerPC/PPCInstrInfo.td, we have pseudos to handle this
for other register classes. Similar pseudos are added in
PPCInstrVSX.td (they must be there, because the "vsrc" register class
definition appears there) for the VSRC register class. The
SELECT_VSRC pseudo is then used in pattern matching for SELECT_CC.
The rest of the patch just adds logic for SELECT_VSRC wherever similar
logic appears for SELECT_VRRC.
There are no new test cases because the existing tests above test
this, along with a variant in test/CodeGen/PowerPC/vsx.ll.
After discussion with Hal, a future patch will add similar _VSFRC
variants to override f64 type handling (currently using F8RC).
llvm-svn: 220385
Currently the VSX support enables use of lxvd2x and stxvd2x for 2x64
types, but does not yet use lxvw4x and stxvw4x for 4x32 types. This
patch adds that support.
As with lxvd2x/stxvd2x, this involves straightforward overriding of
the patterns normally recognized for lvx/stvx, with preference given
to the VSX patterns when VSX is enabled.
In addition, the logic for permitting misaligned memory accesses is
modified so that v4r32 and v4i32 are treated the same as v2f64 and
v2i64 when VSX is enabled. Finally, the DAG generation for unaligned
loads is changed to just use a normal LOAD (which will become lxvw4x)
on P8 and later hardware, where unaligned loads are preferred over
lvsl/lvx/lvx/vperm.
A number of tests now generate the VSX loads/stores instead of
lvx/stvx, so this patch adds VSX variants to those tests. I've also
added <4 x float> tests to the vsx.ll test case, and created a
vsx-p8.ll test case to be used for testing code generation for the
P8Vector feature. For now, that simply tests the unaligned load/store
behavior.
This has been tested along with a temporary patch to enable the VSX
and P8Vector features, with no new regressions encountered with or
without the temporary patch applied.
llvm-svn: 220047
The VSX instruction definitions for lxsdx, lxvd2x, lxvdsx, and lxvw4x
incorrectly use the XForm_1 instruction format, rather than the
XX1Form instruction format. This is likely a pasto when creating
these instructions, which were based on lvx and so forth. This patch
uses the correct format.
The existing reformatting test (test/MC/PowerPC/vsx.s) missed this
because the two formats differ only in that XX1Form has an extension
to the target register field in bit 31. The tests for these
instructions used a target register of 7, so the default of 0 in bit
31 for XForm_1 didn't expose a problem. For register numbers 32-63
this would be noticeable. I've changed the test to use higher
register numbers to verify my change is effective.
llvm-svn: 219416
sitofp from v2i32 to v2f64 ends up generating a SIGN_EXTEND_INREG v2i64 node
(and similarly for v2i16 and v2i8). Even though there are no sign-extension (or
algebraic shifts) for v2i64 types, we can handle v2i32 sign extensions by
converting two and from v2i64. The small trick necessary here is to shift the
i32 elements into the right lanes before the i32 -> f64 step. This is because
of the big Endian nature of the system, we need the i32 portion in the high
word of the i64 elements.
For v2i16 and v2i8 we can do the same, but we first use the default Altivec
shift-based expansion from v2i16 or v2i8 to v2i32 (by casting to v4i32) and
then apply the above procedure.
llvm-svn: 205146
The vector divide and sqrt instructions have high latencies, and the scalar
comparisons are like all of the others. On the P7, permutations take an extra
cycle over purely-simple vector ops.
llvm-svn: 205096
We had stored both f64 values and v2f64, etc. values in the VSX registers. This
worked, but was suboptimal because we would always spill 16-byte values even
through we almost always had scalar 8-byte values. This resulted in an
increase in stack-size use, extra memory bandwidth, etc. To fix this, I've
added 64-bit subregisters of the Altivec registers, and combined those with the
existing scalar floating-point registers to form a class of VSX scalar
floating-point registers. The ABI code has also been enhanced to use this
register class and some other necessary improvements have been made.
llvm-svn: 205075
First, v2f64 vector extract had not been declared legal (and so the existing
patterns were not being used). Second, the patterns for that, and for
scalar_to_vector, should really be a regclass copy, not a subregister
operation, because the VSX registers directly hold both the vector and scalar data.
llvm-svn: 204971
These patterns are dead (because v4f32 stores are currently promoted to v4i32
and stored using Altivec instructions), and also are likely not correct
(because they'd store the vector elements in the opposite order from that
assumed by the rest of the Altivec code).
llvm-svn: 204839
These instructions have access to the complete VSX register file. In addition,
they "swap" the order of the elements so that element 0 (the scalar part) comes
first in memory and element 1 follows at a higher address.
llvm-svn: 204838
v2i64 needs to be a legal VSX type because it is the SetCC result type from
v2f64 comparisons. We need to expand all non-arithmetic v2i64 operations.
This fixes the lowering for v2f64 VSELECT.
llvm-svn: 204828
TableGen will create a lookup table for the A-type FMA instructions providing
their corresponding M-form opcodes. This will be used by upcoming commits.
llvm-svn: 204746
I'm under the impression that we used to infer the isCommutable flag from the
instruction-associated pattern. Regardless, we don't seem to do this (at least
by default) any more. I've gone through all of our instruction definitions, and
marked as commutative all of those that should be trivial to commute (by
exchanging the first two operands). There has been special code for the RL*
instructions, and that's not changed.
Before this change, we had the following commutative instructions:
RLDIMI
RLDIMIo
RLWIMI
RLWIMI8
RLWIMI8o
RLWIMIo
XSADDDP
XSMULDP
XVADDDP
XVADDSP
XVMULDP
XVMULSP
After:
ADD4
ADD4o
ADD8
ADD8o
ADDC
ADDC8
ADDC8o
ADDCo
ADDE
ADDE8
ADDE8o
ADDEo
AND
AND8
AND8o
ANDo
CRAND
CREQV
CRNAND
CRNOR
CROR
CRXOR
EQV
EQV8
EQV8o
EQVo
FADD
FADDS
FADDSo
FADDo
FMADD
FMADDS
FMADDSo
FMADDo
FMSUB
FMSUBS
FMSUBSo
FMSUBo
FMUL
FMULS
FMULSo
FMULo
FNMADD
FNMADDS
FNMADDSo
FNMADDo
FNMSUB
FNMSUBS
FNMSUBSo
FNMSUBo
MULHD
MULHDU
MULHDUo
MULHDo
MULHW
MULHWU
MULHWUo
MULHWo
MULLD
MULLDo
MULLW
MULLWo
NAND
NAND8
NAND8o
NANDo
NOR
NOR8
NOR8o
NORo
OR
OR8
OR8o
ORo
RLDIMI
RLDIMIo
RLWIMI
RLWIMI8
RLWIMI8o
RLWIMIo
VADDCUW
VADDFP
VADDSBS
VADDSHS
VADDSWS
VADDUBM
VADDUBS
VADDUHM
VADDUHS
VADDUWM
VADDUWS
VAND
VAVGSB
VAVGSH
VAVGSW
VAVGUB
VAVGUH
VAVGUW
VMADDFP
VMAXFP
VMAXSB
VMAXSH
VMAXSW
VMAXUB
VMAXUH
VMAXUW
VMHADDSHS
VMHRADDSHS
VMINFP
VMINSB
VMINSH
VMINSW
VMINUB
VMINUH
VMINUW
VMLADDUHM
VMULESB
VMULESH
VMULEUB
VMULEUH
VMULOSB
VMULOSH
VMULOUB
VMULOUH
VNMSUBFP
VOR
VXOR
XOR
XOR8
XOR8o
XORo
XSADDDP
XSMADDADP
XSMAXDP
XSMINDP
XSMSUBADP
XSMULDP
XSNMADDADP
XSNMSUBADP
XVADDDP
XVADDSP
XVMADDADP
XVMADDASP
XVMAXDP
XVMAXSP
XVMINDP
XVMINSP
XVMSUBADP
XVMSUBASP
XVMULDP
XVMULSP
XVNMADDADP
XVNMADDASP
XVNMSUBADP
XVNMSUBASP
XXLAND
XXLNOR
XXLOR
XXLXOR
This is a by-inspection change, and I'm not sure how to write a reliable test
case. I would like advice on this, however.
llvm-svn: 204609
When VSX is available, these instructions should be used in preference to the
older variants that only have access to the scalar floating-point registers.
llvm-svn: 204559
VSX is an ISA extension supported on the POWER7 and later cores that enhances
floating-point vector and scalar capabilities. Among other things, this adds
<2 x double> support and generally helps to reduce register pressure.
The interesting part of this ISA feature is the register configuration: there
are 64 new 128-bit vector registers, the 32 of which are super-registers of the
existing 32 scalar floating-point registers, and the second 32 of which overlap
with the 32 Altivec vector registers. This makes things like vector insertion
and extraction tricky: this can be free but only if we force a restriction to
the right register subclass when needed. A new "minipass" PPCVSXCopy takes care
of this (although it could do a more-optimal job of it; see the comment about
unnecessary copies below).
Please note that, currently, VSX is not enabled by default when targeting
anything because it is not yet ready for that. The assembler and disassembler
are fully implemented and tested. However:
- CodeGen support causes miscompiles; test-suite runtime failures:
MultiSource/Benchmarks/FreeBench/distray/distray
MultiSource/Benchmarks/McCat/08-main/main
MultiSource/Benchmarks/Olden/voronoi/voronoi
MultiSource/Benchmarks/mafft/pairlocalalign
MultiSource/Benchmarks/tramp3d-v4/tramp3d-v4
SingleSource/Benchmarks/CoyoteBench/almabench
SingleSource/Benchmarks/Misc/matmul_f64_4x4
- The lowering currently falls back to using Altivec instructions far more
than it should. Worse, there are some things that are scalarized through the
stack that shouldn't be.
- A lot of unnecessary copies make it past the optimizers, and this needs to
be fixed.
- Many more regression tests are needed.
Normally, I'd fix these things prior to committing, but there are some
students and other contributors who would like to work this, and so it makes
sense to move this development process upstream where it can be subject to the
regular code-review procedures.
llvm-svn: 203768
