my last patch to this file.
The issue there was that all uses of an IV inside a loop
are actually references to Base[IV*2], and there was one
use outside that was the same but LSR didn't see the base
or the scaling because it didn't recurse into uses outside
the loop; thus, it used base+IV*scale mode inside the loop
instead of pulling base out of the loop. This was extra bad
because register pressure later forced both base and IV into
memory. Doing that recursion, at least enough
to figure out addressing modes, is a good idea in general;
the change in AddUsersIfInteresting does this. However,
there were side effects....
It is also possible for recursing outside the loop to
introduce another IV where there was only 1 before (if
the refs inside are not scaled and the ref outside is).
I don't think this is a common case, but it's in the testsuite.
It is right to be very aggressive about getting rid of
such introduced IVs (CheckForIVReuse and the handling of
nonzero RewriteFactor in StrengthReduceStridedIVUsers).
In the testcase in question the new IV produced this way
has both a nonconstant stride and a nonzero base, neither
of which was handled before. And when inserting
new code that feeds into a PHI, it's right to put such
code at the original location rather than in the PHI's
immediate predecessor(s) when the original location is outside
the loop (a case that couldn't happen before)
(RewriteInstructionToUseNewBase); better to avoid making
multiple copies of it in this case.
Also, the mechanism for keeping SCEV's corresponding to GEP's
no longer works, as the GEP might change after its SCEV
is remembered, invalidating the SCEV, and we might get a bad
SCEV value when looking up the GEP again for a later loop.
This also couldn't happen before, as we weren't recursing
into GEP's outside the loop.
I owe some testcases for this, want to get it in for nightly runs.
llvm-svn: 61362
my last patch to this file.
The issue there was that all uses of an IV inside a loop
are actually references to Base[IV*2], and there was one
use outside that was the same but LSR didn't see the base
or the scaling because it didn't recurse into uses outside
the loop; thus, it used base+IV*scale mode inside the loop
instead of pulling base out of the loop. This was extra bad
because register pressure later forced both base and IV into
memory. Doing that recursion, at least enough
to figure out addressing modes, is a good idea in general;
the change in AddUsersIfInteresting does this. However,
there were side effects....
It is also possible for recursing outside the loop to
introduce another IV where there was only 1 before (if
the refs inside are not scaled and the ref outside is).
I don't think this is a common case, but it's in the testsuite.
It is right to be very aggressive about getting rid of
such introduced IVs (CheckForIVReuse and the handling of
nonzero RewriteFactor in StrengthReduceStridedIVUsers).
In the testcase in question the new IV produced this way
has both a nonconstant stride and a nonzero base, neither
of which was handled before. (This patch does not handle
all the cases where this can happen.) And when inserting
new code that feeds into a PHI, it's right to put such
code at the original location rather than in the PHI's
immediate predecessor(s) when the original location is outside
the loop (a case that couldn't happen before)
(RewriteInstructionToUseNewBase); better to avoid making
multiple copies of it in this case.
Everything above is exercised in
CodeGen/X86/lsr-negative-stride.ll (and ifcvt4 in ARM which is
the same IR).
llvm-svn: 61178
loops when they can be subsumed into addressing modes.
Change X86 addressing mode check to realize that
some PIC references need an extra register.
(I believe this is correct for Linux, if not, I'm sure
someone will tell me.)
llvm-svn: 60608
figuring out the base of the IV. This produces better
code in the example. (Addresses use (IV) instead of
(BASE,IV) - a significant improvement on low-register
machines like x86).
llvm-svn: 60374
instead of std::sort. This shrinks the release-asserts LSR.o file
by 1100 bytes of code on my system.
We should start using array_pod_sort where possible.
llvm-svn: 60335
buggy rewrite, this notifies ScalarEvolution of a pending instruction
about to be removed and then erases it, instead of erasing it then
notifying.
llvm-svn: 60329
LoopPass*.
- Although less precise, this means they can be used in clients
without RTTI (who would otherwise need to include LoopPass.h, which
eventually includes things using dynamic_cast). This was the
simplest solution that presented itself, but I am happy to use a
better one if available.
llvm-svn: 58010
cases. See the comment above OptimizeSMax for the full story, and
the testcase for an example. This cancels out a pessimization
commonly attributed to indvars, and will allow us to lift some of
the artificial throttles in indvars, rather than add new ones.
llvm-svn: 56230
leads into a cycle involving a different PHI, LSR got stuck running
around that cycle looking for the original PHI. To avoid this, keep
track of visited PHIs and stop searching if we see one more than once.
This fixes PR2570.
llvm-svn: 53879
1. LSR runOnLoop is always returning false regardless if any transformation is made.
2. AddUsersIfInteresting can create new instructions that are added to DeadInsts. But there is a later early exit which prevents them from being freed.
llvm-svn: 53193
when changing the stride of a comparison so that it's slightly
more precise, by having it scan the instruction list to determine
if there is a use of the condition after the point where the
condition will be inserted.
llvm-svn: 52371