Delete the Kill and Def markers in BlockInfo. They are no longer
necessary when BlockInfo describes a continuous live range.
This only affects the relatively rare kind of basic block where a live
range looks like this:
|---x o---|
Now live range splitting can pretend that it is looking at two blocks:
|---x
o---|
This allows the code to be simplified a bit.
llvm-svn: 132245
It is important that this function returns the same number of live blocks as
countLiveBlocks(CurLI) because live range splitting uses the number of live
blocks to ensure it is making progress.
This is in preparation of supporting duplicate UseBlock entries for basic blocks
that have a virtual register live-in and live-out, but not live-though.
llvm-svn: 132244
Register coalescing can sometimes create live ranges that end in the middle of a
basic block without any killing instruction. When SplitKit detects this, it will
repair the live range by shrinking it to its uses.
Live range splitting also needs to know about this. When the range shrinks so
much that it becomes allocatable, live range splitting fails because it can't
find a good split point. It is paranoid about making progress, so an allocatable
range is considered an error.
The coalescer should really not be creating these bad live ranges. They appear
when coalescing dead copies.
llvm-svn: 130787
These intervals are allocatable immediately after splitting, but they may be
evicted because of later splitting. This is rare, but when it happens they
should be split again.
The remainder intervals that cannot be allocated after splitting still move
directly to spilling.
SplitEditor::finish can optionally provide a mapping from new live intervals
back to the original interval indexes returned by openIntv().
Each original interval index can map to multiple new intervals after connected
components have been separated. Dead code elimination may also add existing
intervals to the list.
The reverse mapping allows the SplitEditor client to treat the new intervals
differently depending on the split region they came from.
llvm-svn: 129925
The transferValues() function can now handle both singly and multiply defined
values, as long as the resulting live range is known. Only rematerialized values
have their live range recomputed by extendRange().
The updateSSA() function can now insert PHI values in bulk across multiple
values in multiple target registers in one pass. The list of blocks received
from transferValues() is in layout order which seems to work well for the
iterative algorithm. Blocks from extendRange() are still in reverse BFS order,
but this function is used so rarely now that it doesn't matter.
llvm-svn: 129580
This merges the behavior of splitSingleBlocks into splitAroundRegion, so the
RS_Region and RS_Block register stages can be coalesced. That means the leftover
intervals after region splitting go directly to spilling instead of a second
pass of per-block splitting.
llvm-svn: 129379
It is common for large live ranges to have few basic blocks with register uses
and many live-through blocks without any uses. This approach grows the Hopfield
network incrementally around the use blocks, completely avoiding checking
interference for some through blocks.
llvm-svn: 129188
About 90% of the relevant blocks are live-through without uses, and the only
information required about them is their number. This saves memory and enables
later optimizations that need to look at only the use-blocks.
llvm-svn: 128985
This allows us to always keep the smaller slot for an instruction which is what
we want when a register has early clobber defines.
Drop the UsingInstrs set and the UsingBlocks map. They are no longer needed.
llvm-svn: 128886
inlined path for the common case.
Most basic blocks don't contain a call that may throw, so the last split point
os simply the first terminator.
llvm-svn: 128874
LiveRangeEdit::eliminateDeadDefs() will eventually be used by coalescing,
splitting, and spilling for dead code elimination. It can delete chains of dead
instructions as long as there are no dependency loops.
llvm-svn: 127287
The coalescer can in very rare cases leave too large live intervals around after
rematerializing cheap-as-a-move instructions.
Linear scan doesn't really care, but live range splitting gets very confused
when a live range is killed by a ghost instruction.
I will fix this properly in the coalescer after 2.9 branches.
llvm-svn: 127096
Values that map to a single new value in a new interval after splitting don't
need new PHIDefs, and if the parent value was never rematerialized the live
range will be the same.
llvm-svn: 126894
Extract the updateSSA() method from the too long extendRange().
LiveOutCache can be shared among all the new intervals since there is at most
one of the new ranges live out from each basic block.
llvm-svn: 126818
This method could probably be used by LiveIntervalAnalysis::shrinkToUses, and
now it can use extendIntervalEndTo() which coalesces ranges.
llvm-svn: 126803
The value map is currently not used, all values are 'complex mapped' and
LiveIntervalMap::mapValue is used to dig them out.
This is the first step in a series changes leading to the removal of
LiveIntervalMap. Its data structures can be shared among all the live intervals
created by a split, so it is wasteful to create a copy for each.
llvm-svn: 126800
An original endpoint is an instruction that killed or defined the original live
range before any live ranges were split.
When splitting global live ranges, avoid creating local live ranges without any
original endpoints. We may still create global live ranges without original
endpoints, but such a range won't be split again, and live range splitting still
terminates.
llvm-svn: 126151
A local live range is live in a single basic block. If such a range fails to
allocate, try to find a sub-range that would get a larger spill weight than its
interference.
llvm-svn: 125764
If a live range is used by a terminator instruction, and that live range needs
to leave the block on the stack or in a different register, it can be necessary
to have both sides of the split live at the terminator instruction.
Example:
%vreg2 = COPY %vreg1
JMP %vreg1
Becomes after spilling %vreg2:
SPILL %vreg1
JMP %vreg1
The spill doesn't kill the register as is normally the case.
llvm-svn: 125102
The greedy register allocator revealed some problems with the value mapping in
SplitKit. We would sometimes start mapping values before all defs were known,
and that could change a value from a simple 1-1 mapping to a multi-def mapping
that requires ssa update.
The new approach collects all defs and register assignments first without
filling in any live intervals. Only when finish() is called, do we compute
liveness and mapped values. At this time we know with certainty which values map
to multiple values in a split range.
This also has the advantage that we can compute live ranges based on the
remaining uses after rematerializing at split points.
The current implementation has many opportunities for compile time optimization.
llvm-svn: 124765
Analyze the live range's behavior entering and leaving basic blocks. Compute an
interference pattern for each allocation candidate, and use SpillPlacement to
find an optimal region where that register can be live.
This code is still not enabled.
llvm-svn: 123774
