After Ulrich's r180677 (thanks!) TableGen is intelligent enough to
handle tied constraints involving complex operands properly, so
virtually all of the ARM custom converters are now unnecessary.
llvm-svn: 186810
indirect branches correctly. Under some circumstances, this led to the deletion
of basic blocks that were the destination of indirect branches. In that case it
left indirect branches to nowhere in the code.
This patch replaces, and is more general than either of the previous fixes for
indirect-branch-analysis issues, r181161 and r186461.
For other branches (not indirect) this refactor should have *almost* identical
behavior to the previous version. There are some corner cases where this
refactor is able to analyze blocks that the previous version could not (e.g.
this necessitated the update to thumb2-ifcvt2.ll).
<rdar://problem/14464830>
llvm-svn: 186735
The atomic tests assume the two-operand forms, so I've restricted them to z10.
Running and-01.ll, or-01.ll and xor-01.ll for z196 as well as z10 shows why
using convertToThreeAddress() is better than exposing the three-operand forms
first and then converting back to two operands where possible (which is what
I'd originally tried). Using the three-operand form first stops us from
taking advantage of NG, OG and XG for spills.
llvm-svn: 186683
This first step just adds definitions for SLLK, SRLK and SRAK.
The next patch will actually make use of them during codegen.
insn-bad.s tests that some form of error is reported when using these
instructions on z10. More work is needed to get the "instruction requires:
distinct-ops" that we'd ideally like, so I've stubbed that part out for now.
I'll come back and make it mandatory once the necessary changes are in.
llvm-svn: 186680
The original code only folded SRA into ROTATE ... SELECTED BITS
if there was no outer shift. This patch splits out that check
and generalises it slightly. The extra cases aren't really that
interesting, but this is paving the way for RNSBG support.
llvm-svn: 186571
In hindsight, using "RISBG" for something that can be any type of
R.SBG instruction was a bit confusing, so this renames it to RxSBG.
That might not be the best choice either, since there is an instruction
called RXSBG, but hopefully the lower-case letter stands out enough.
While there I fixed a couple of GNUisms that had crept in --
sorry about that!
llvm-svn: 186569
Support for dynamic stack alignments in the PPC backend has been unfinished, in
part because it depends on dynamic stack realignment (which I only just
recently implemented fully). Now we can also support dynamic allocas with
higher than the default target stack alignment (16 bytes).
In order to round-up the requested size to the maximum requested alignment, we
need an additional register to hold the rounded-up size. We're already using one
scavenged register to hold the previous stack-pointer value (which needs to be
stored with the signal-safe stdux update), and so when we have dynamic allocas
and a large alignment, we allocate two emergency spill slots for the scavenger.
llvm-svn: 186562
First, this changes the base-pointer implementation to remove an unnecessary
complication (and one that is incompatible with how builtin SjLj is
implemented): instead of using r31 as the base pointer when it is not needed as
a frame pointer, now the base pointer will always be r30 when needed.
Second, we introduce another pseudo register, BP, which is used just like the FP
pseudo register to refer to the base register before we know for certain what
register it will be.
Third, we now save BP into the jmp_buf, and restore r30 from that slot in
longjmp. If the function that called setjmp did not use a base pointer, then
r30 will be overwritten by the setjmp-calling-function's restore code. FP
restoration (which is restored into r31) works the same way.
llvm-svn: 186545
My patch 'r183551 - ARM FastISel integer sext/zext improvements' was incorrect when emitting ARM register-immediate ASR, LSL, LSR instructions: they are pseudo-instructions in ARMInstrInfo.td and I should have used MOVsi instead.
This is not an issue when code is generated through a .s file, but is an issue when generated straight to a .o (-filetype=obj).
llvm-svn: 186489
Because the builtin longjmp implementation uses a CTR-based indirect jump, when
the control flow arrives at the builtin setjmp call, the CTR register has
necessarily been clobbered. Correspondingly, this adds CTR to the list of
implicit definitions of the builtin setjmp pseudo instruction.
We don't need to add CTR to the implicit definitions of builtin longjmp
because, even though it does clobber the CTR register, the control flow cannot
return to inside the loop unless there is also a builtin setjmp call.
llvm-svn: 186488
