it follows the order of the enum, not alphabetical.
The motivation is to make -mattr=+ssse3,+sse41
select SSE41 as it ought to. Added "ignored"
enum values of 0 to PPC and SPU to avoid compiler
warnings.
llvm-svn: 47143
Added ISD::DECLARE node type to represent llvm.dbg.declare intrinsic. Now the intrinsic calls are lowered into a SDNode and lives on through out the codegen passes.
For now, since all the debugging information recording is done at isel time, when a ISD::DECLARE node is selected, it has the side effect of also recording the variable. This is a short term solution that should be fixed in time.
llvm-svn: 46659
- Expand tabs... (poss 80-col violations, will get them later...)
- Consolidate logic for SelectDFormAddr and SelectDForm2Addr into a single
function, simplifying maintenance. Also reduced custom instruction
generation for SPUvecinsert/INSERT_MASK.
llvm-svn: 46544
and StoreSDNode into their common base class LSBaseSDNode. Member
functions getLoadedVT and getStoredVT are replaced with the common
getMemoryVT to simplify code that will handle both loads and stores.
llvm-svn: 46538
only two addressing mode nodes, SPUaform and SPUindirect (vice the
three previous ones, SPUaform, SPUdform and SPUxform). This improves
code somewhat because we now avoid using reg+reg addressing when
it can be avoided. It also simplifies the address selection logic,
which was the main point for doing this.
Also, for various global variables that would be loaded using SPU's
A-form addressing, prefer D-form offs[reg] addressing, keeping the
base in a register if the variable is used more than once.
llvm-svn: 46483
Fixed CellSPU's A-form (local store) address mode, so that all globals,
externals, constant pool and jump table symbols are now wrapped within
a SPUISD::AFormAddr pseudo-instruction. This now identifies all local
store memory addresses, although it requires a bit of legerdemain during
instruction selection to properly select loads to and stores from local
store, properly generating "LQA" instructions.
Also added mul_ops.ll test harness for exercising integer multiplication.
llvm-svn: 46142
1. Legalize now always promotes truncstore of i1 to i8.
2. Remove patterns and gunk related to truncstore i1 from targets.
3. Rename the StoreXAction stuff to TruncStoreAction in TLI.
4. Make the TLI TruncStoreAction table a 2d table to handle from/to conversions.
5. Mark a wide variety of invalid truncstores as such in various targets, e.g.
X86 currently doesn't support truncstore of any of its integer types.
6. Add legalize support for truncstores with invalid value input types.
7. Add a dag combine transform to turn store(truncate) into truncstore when
safe.
The later allows us to compile CodeGen/X86/storetrunc-fp.ll to:
_foo:
fldt 20(%esp)
fldt 4(%esp)
faddp %st(1)
movl 36(%esp), %eax
fstps (%eax)
ret
instead of:
_foo:
subl $4, %esp
fldt 24(%esp)
fldt 8(%esp)
faddp %st(1)
fstps (%esp)
movl 40(%esp), %eax
movss (%esp), %xmm0
movss %xmm0, (%eax)
addl $4, %esp
ret
llvm-svn: 46140
- struct_2.ll: Completely unaligned load/store testing
- call_indirect.ll, struct_1.ll: Add test lines to exercise
X-form [$reg($reg)] addressing
At this point, loads and stores should be under control (he says
in an optimistic tone of voice.)
llvm-svn: 45882
- Cleaned up custom load/store logic, common code is now shared [see note
below], cleaned up address modes
- More test cases: various intrinsics, structure element access (load/store
test), updated target data strings, indirect function calls.
Note: This patch contains a refactoring of the LoadSDNode and StoreSDNode
structures: they now share a common base class, LSBaseSDNode, that
provides an interface to their common functionality. There is some hackery
to access the proper operand depending on the derived class; otherwise,
to do a proper job would require finding and rearranging the SDOperands
sent to StoreSDNode's constructor. The current refactor errs on the
side of being conservatively and backwardly compatible while providing
functionality that reduces redundant code for targets where loads and
stores are custom-lowered.
llvm-svn: 45851
instead of "ISD::STORE". This allows us to mark target-specific dag
nodes as storing (such as ppc byteswap stores). This allows us to remove
more explicit isStore flags from the .td files.
Finally, add a warning for when a .td file contains an explicit
isStore and tblgen is able to infer it.
llvm-svn: 45654
a header file from libcodegen. This violates a layering order: codegen
depends on target, not the other way around. The fix to this is to
split TII into two classes, TII and TargetInstrInfoImpl, which defines
stuff that depends on libcodegen. It is defined in libcodegen, where
the base is not.
llvm-svn: 45475
that "machine" classes are used to represent the current state of
the code being compiled. Given this expanded name, we can start
moving other stuff into it. For now, move the UsedPhysRegs and
LiveIn/LoveOuts vectors from MachineFunction into it.
Update all the clients to match.
This also reduces some needless #includes, such as MachineModuleInfo
from MachineFunction.
llvm-svn: 45467
e.g. MO.isMBB() instead of MO.isMachineBasicBlock(). I don't plan on
switching everything over, so new clients should just start using the
shorter names.
Remove old long accessors, switching everything over to use the short
accessor: getMachineBasicBlock() -> getMBB(),
getConstantPoolIndex() -> getIndex(), setMachineBasicBlock -> setMBB(), etc.
llvm-svn: 45464
