Add pseudo conditional store instructions, so that we use:
branch foo:
store
foo:
instead of:
load
branch foo:
move
foo:
store
z196 has real 32-bit and 64-bit conditional stores, but we don't use
any z196 instructions yet.
llvm-svn: 185065
Unlike most -- hopefully "all other", but I'm still checking -- memory
instructions we support, LOAD REVERSED and STORE REVERSED may access
the memory location several times. This means that they are not suitable
for volatile loads and stores.
This patch is a prerequisite for better atomic load and store support.
The same principle applies there: almost all memory instructions we
support are inherently atomic ("block concurrent"), but LOAD REVERSED
and STORE REVERSED are exceptions.
Other instructions continue to allow volatile operands. I will add
positive "allows volatile" tests at the same time as the "allows atomic
load or store" tests.
llvm-svn: 183002
The code to distinguish between unaligned and aligned addresses was
already there, so this is mostly just a switch-on-and-test process.
llvm-svn: 182920
This patch adds support for the CRJ and CGRJ instructions. Support for
the immediate forms will be a separate patch.
The architecture has a large number of comparison instructions. I think
it's generally better to concentrate on using the "best" comparison
instruction first and foremost, then only use something like CRJ if
CR really was the natual choice of comparison instruction. The patch
therefore opportunistically converts separate CR and BRC instructions
into a single CRJ while emitting instructions in ISelLowering.
llvm-svn: 182764
Before this change, the SystemZ backend would use BRCL for all branches
and only consider shortening them to BRC when generating an object file.
E.g. a branch on equal would use the JGE alias of BRCL in assembly output,
but might be shortened to the JE alias of BRC in ELF output. This was
a useful first step, but it had two problems:
(1) The z assembler isn't traditionally supposed to perform branch shortening
or branch relaxation. We followed this rule by not relaxing branches
in assembler input, but that meant that generating assembly code and
then assembling it would not produce the same result as going directly
to object code; the former would give long branches everywhere, whereas
the latter would use short branches where possible.
(2) Other useful branches, like COMPARE AND BRANCH, do not have long forms.
We would need to do something else before supporting them.
(Although COMPARE AND BRANCH does not change the condition codes,
the plan is to model COMPARE AND BRANCH as a CC-clobbering instruction
during codegen, so that we can safely lower it to a separate compare
and long branch where necessary. This is not a valid transformation
for the assembler proper to make.)
This patch therefore moves branch relaxation to a pre-emit pass.
For now, calls are still shortened from BRASL to BRAS by the assembler,
although this too is not really the traditional behaviour.
The first test takes about 1.5s to run, and there are likely to be
more tests in this vein once further branch types are added. The feeling
on IRC was that 1.5s is a bit much for a single test, so I've restricted
it to SystemZ hosts for now.
The patch exposes (and fixes) some typos in the main CodeGen/SystemZ tests.
A later patch will remove the {{g}}s from that directory.
llvm-svn: 182274
This adds all CodeGen tests for the SystemZ target.
This version of the patch incorporates feedback from a review by
Sean Silva. Thanks to all reviewers!
Patch by Richard Sandiford.
llvm-svn: 181204
Note that this actually changes code generation, and someone who
understands this target better should check the changes.
- R12Q is now allocatable. I think it was omitted from the allocation
order by mistake since it isn't reserved. It as apparently used as a
GOT pointer sometimes, and it should probably be reserved if that is
the case.
- The GR64 registers are allocated in a different order now. The
register allocator will automatically put the CSRs last. There were
other changes to the order that may have been significant.
The test fix is because r0 and r1 swapped places in the allocation order.
llvm-svn: 133067
replace the check with the appropriate predicate. Modify the testcase to reflect
the correct code. (It should be saving callee-saved registers on the stack
allocated by the calling fuction.)
llvm-svn: 103829
(OP (trunc x), (trunc y)) -> (trunc (OP x, y))
Unfortunately this simple change causes dag combine to infinite looping. The problem is the shrink demanded ops optimization tend to canonicalize expressions in the opposite manner. That is badness. This patch disable those optimizations in dag combine but instead it is done as a late pass in sdisel.
This also exposes some deficiencies in dag combine and x86 setcc / brcond lowering. Teach them to look pass ISD::TRUNCATE in various places.
llvm-svn: 92849
