We now emit the compiler generated divide by zero check that was needed for the
MSVC routines. We construct a psuedo-instruction for the DBZ check as the
operation requires splitting up the BB. For the 64-bit operations, we need to
custom expand the node as we need to insert the DBZ check and then emit the
libcall to the appropriate name. Because this is target specific, it seemed
better to reproduce the expansion operation from the target-agnostic type
legalization rather than sink this there to avoid the duplication. The division
library calls now match MSVC semantically.
llvm-svn: 248561
Allow a target to do something other than search for copies
that will avoid cross register bank copies.
Implement for SI by only rewriting the most basic copies,
so it should look through anything like a subregister extract.
I'm not entirely satisified with this because it seems like
eliminating a reg_sequence that isn't fully used should work
generically for all targets without them having to override
something. However, it seems to be tricky to have a simple
implementation of this without rewriting to invalid kinds
of subregister copies on some targets.
I'm not sure if there is currently a generic way to easily check
if a subregister index would be valid for the current use.
The current set of TargetRegisterInfo::get*Class functions don't
quite behave like I would expect (e.g. getSubClassWithSubReg
returns the maximal register class rather than the minimal), so
I'm not sure how to make the generic test keep searching if
SrcRC:SrcSubReg is a valid replacement for DefRC:DefSubReg. Making
the default implementation to check for simple copies breaks
a variety of ARM and x86 tests by producing illegal subregister uses.
The ARM tests are not actually changed since it should still be using
the same sharesSameRegisterFile implementation, this just relaxes
them to not check for specific registers.
llvm-svn: 248478
This time, the issue is that we weren't accounting for the possibility that
aligned DPRs could have been stored after the final "push" in a prologue. When
that happened we effectively moved a "sub sp, #N" from below the aligned stores
to above them, and everything went to pot.
To make it worse, I'd actually committed something testing that we produced
wrong code, so the test update is tiny.
llvm-svn: 248437
ARM counterpart to r248291:
In the comparison failure block of a cmpxchg expansion, the initial
ldrex/ldxr will not be followed by a matching strex/stxr.
On ARM/AArch64, this unnecessarily ties up the execution monitor,
which might have a negative performance impact on some uarchs.
Instead, release the monitor in the failure block.
The clrex instruction was designed for this: use it.
Also see ARMARM v8-A B2.10.2:
"Exclusive access instructions and Shareable memory locations".
Differential Revision: http://reviews.llvm.org/D13033
llvm-svn: 248294
The vext pseudo-instruction takes the number of elements that need to be
extracted, not the number of bytes. Hence, use the number of elements
directly instead of scaling them with a factor.
Reviewers: Silviu Baranga, James Molloy
(not reflected in the differential revision)
Differential Revision: http://reviews.llvm.org/D12974
llvm-svn: 248208
In if-conversion, there is a utility function MergeBlocks() that is used to merge blocks. However, when new edges are built in this function the edge weight is either not provided or not updated properly, leading to a modified CFG with incorrect edge weights. This patch corrects this issue.
Differential Revision: http://reviews.llvm.org/D12513
llvm-svn: 248030
In ARMBaseInstrInfo::isProfitableToIfCvt(), there is a simple cost model in which the number of cycles is scaled by a probability to estimate the cost. However, when the number of cycles is small (which is usually the case), there is a precision issue after the computation. To avoid this issue, this patch scales those cycles by 1024 (chosen to make the multiplication a litter faster) before they are scaled by the probability. Other variables are also scaled up for the final comparison.
Differential Revision: http://reviews.llvm.org/D12742
llvm-svn: 248018
- Strenghten the logic to be sure we hoist the restore point out of the current
loop. (The fixes a bug with infinite loop, added as part of the patch.)
- Walk over the exit blocks of the current loop to conver to the desired restore
point in one iteration of the update loop.
llvm-svn: 247958
Turning (op x (mul y k)) into (op x (lsl (mul y k>>n) n)) is beneficial when
we can do the lsl as a shifted operand and the resulting multiply constant is
simpler to generate.
Do this by doing the transformation when trying to select a shifted operand,
as that ensures that it actually turns out better (the alternative would be to
do it in PreprocessISelDAG, but we don't know for sure there if extracting the
shift would allow a shifted operand to be used).
Differential Revision: http://reviews.llvm.org/D12196
llvm-svn: 247569
The tests in isVTRNMask and isVTRN_v_undef_Mask should also check that the elements of the upper and lower half of the vectorshuffle occur in the correct order when both halves are used. Without this test the code assumes that it is correct to use vector transpose (vtrn) for the masks <1, 1, 0, 0> and <1, 3, 0, 2>, among others, but the transpose actually incorrectly generates shuffles for <0, 0, 1, 1> and <0, 2, 1, 3> in this case.
Patch by Jeroen Ketema!
llvm-svn: 247254
In searching for a fix for the underlying code-quality bug highlighted by
r246937 (that SDAG simplification can lead to us generating an ISD::OR node
with a constant zero LHS), I ran across this:
We generically canonicalize commutative binary-operation nodes in SDAG getNode
so that, if only one operand is a constant, it will be on the RHS. However, we
were doing this only after a bunch of constant-based simplification checks that
all assume this canonical form (that any constant will be on the RHS). Moving
the operand-swapping canonicalization prior to these checks seems like the
right thing to do (and, as it turns out, causes SDAG to completely fold away the
computation in test/CodeGen/ARM/2012-11-14-subs_carry.ll, just like InstCombine
would do).
llvm-svn: 246938
The code introduced in r244314 assumed that EXTRACT_VECTOR_ELT only
takes constant indices, but it does accept variables.
Bail out for those: we can't use them, as the shuffles we want to
reconstruct do require constant masks.
llvm-svn: 246594
Summary:
Interleaved access lowering removes a memory operation and a
sequence of vector shuffles and replaces it with a series of
memory operations. This should be always beneficial.
This pass in only enabled on ARM/AArch64.
Reviewers: rengolin
Subscribers: aemerson, llvm-commits, rengolin
Differential Revision: http://reviews.llvm.org/D12145
llvm-svn: 246540
Currently, when edge weights are assigned to edges that are created when lowering switch statement, the weight on the edge to default statement (let's call it "default weight" here) is not considered. We need to distribute this weight properly. However, without value profiling, we have no idea how to distribute it. In this patch, I applied the heuristic that this weight is evenly distributed to successors.
For example, given a switch statement with cases 1,2,3,5,10,11,20, and every edge from switch to each successor has weight 10. If there is a binary search tree built to test if n < 10, then its two out-edges will have weight 4x10+10/2 = 45 and 3x10 + 10/2 = 35 respectively (currently they are 40 and 30 without considering the default weight). Each distribution (which is 5 here) will be stored in each SwitchWorkListItem for further distribution.
There are some exceptions:
For a jump table header which doesn't have any edge to default statement, we don't distribute the default weight to it.
For a bit test header which covers a contiguous range and hence has no edges to default statement, we don't distribute the default weight to it.
When the branch checks a single value or a contiguous range with no edge to default statement, we don't distribute the default weight to it.
In other cases, the default weight is evenly distributed to successors.
Differential Revision: http://reviews.llvm.org/D12418
llvm-svn: 246522
This is especially visible in softfp mode, for example in the implementation of libm fabs/fneg functions. If we have:
%1 = vmovdrr r0, r1
%2 = fabs %1
then move the fabs before the vmovdrr:
%1 = and r1, #0x7FFFFFFF
%2 = vmovdrr r0, r1
This is never a lose, and could be a serious win because the vmovdrr may be followed by a vmovrrd, which would enable us to remove the conversion into FPRs completely.
We already do this for f32, but not for f64. Tests are added for both.
llvm-svn: 246360
I'm working on adding !dbg attachments to functions (PR23367), which
we'll use to determine the canonical subprogram for a function (instead
of the `subprograms:` array in the compile units). This updates a few
old tests in preparation.
Transforms/Mem2Reg/ConvertDebugInfo2.ll had an old-style grep+count
based test that would start to fail because I've added an extra line
with `!dbg`. Instead, explicitly `CHECK` for what I think the test
actually cares about.
All three testcases have subprograms with a valid `function:` reference
-- which means my upgrade script will add a `!dbg` attachment -- but
that aren't referenced from any compile unit. I suspect these testcases
were handreduced over-zealously (or have bitrotted?). Add a reference
from the compile unit so that upcoming Verifier checks won't fail here.
llvm-svn: 246351
As a follow-up to r246098, require `DISubprogram` definitions
(`isDefinition: true`) to be 'distinct'. Specifically, add an assembler
check, a verifier check, and bitcode upgrading logic to combat testcase
bitrot after the `DIBuilder` change.
While working on the testcases, I realized that
test/Linker/subprogram-linkonce-weak-odr.ll isn't relevant anymore. Its
purpose was to check for a corner case in PR22792 where two subprogram
definitions match exactly and share the same metadata node. The new
verifier check, requiring that subprogram definitions are 'distinct',
precludes that possibility.
I updated almost all the IR with the following script:
git grep -l -E -e '= !DISubprogram\(.* isDefinition: true' |
grep -v test/Bitcode |
xargs sed -i '' -e 's/= \(!DISubprogram(.*, isDefinition: true\)/= distinct \1/'
Likely some variant of would work for out-of-tree testcases.
llvm-svn: 246327
Currently, when lowering switch statement and a new basic block is built for jump table / bit test header, the edge to this new block is not assigned with a correct weight. This patch collects the edge weight from all its successors and assign this sum of weights to the edge (and also the other fall-through edge). Test cases are adjusted accordingly.
Differential Revision: http://reviews.llvm.org/D12166#fae6eca7
llvm-svn: 246104
The FP16_TO_FP node only uses the bottom 16 bits of its input, so the
following pattern can be optimised by removing the AND:
(FP16_TO_FP (AND op, 0xffff)) -> (FP16_TO_FP op)
This is a common pattern for ARM targets when functions have __fp16
arguments, as they are passed as floats (so that they get passed in the
correct registers), but then bitcast and truncated to ignore the top 16
bits.
llvm-svn: 245832
This is intended to improve code generation for GEPs, as the index value is
shifted by the element size and in GEPs of multi-dimensional arrays the index
of higher dimensions is multiplied by the lower dimension size.
Differential Revision: http://reviews.llvm.org/D12197
llvm-svn: 245689
Summary:
The mid-end was generating vector smin/smax/umin/umax nodes, but
we were using vbsl to generatate the code. This adds the vmin/vmax
patterns and a test to check that we are now generating vmin/vmax
instructions.
Reviewers: rengolin, jmolloy
Subscribers: aemerson, rengolin, llvm-commits
Differential Revision: http://reviews.llvm.org/D12105
llvm-svn: 245439
These only get generated if the target supports them. If one of the variants is not legal and the other is, and it is safe to do so, the other variant will be emitted.
For example on AArch32 (V8), we have scalar fminnm but not fmin.
Fix up a couple of tests while we're here - one now produces better code, and the other was just plain wrong to start with.
llvm-svn: 245196
This patch makes the Darwin ARM backend take advantage of TargetParser. It
also teaches TargetParser about ARMV7K for the first time. This makes target
triple parsing more consistent across llvm.
Differential Revision: http://reviews.llvm.org/D11996
llvm-svn: 245081
They rely on global fast-math options, but soon ISel will rely only on fast-math flags on the instructions themselves. Rip the fast checks out into their own file so we can mark their instructions as fast.
llvm-svn: 244914
Other than PC-relative loads/store the patterns that match the various
load/store addressing modes have the same complexity, so the order that they
are matched is the order that they appear in the .td file.
Rearrange the instruction definitions in ARMInstrThumb.td, and make use of
AddedComplexity for PC-relative loads, so that the instruction matching order
is the order that results in the simplest selection logic. This also makes
register-offset load/store be selected when it should, as previously it was
only selected for too-large immediate offsets.
Differential Revision: http://reviews.llvm.org/D11800
llvm-svn: 244882
r242520 was reverted in r244313 as the expected behaviour of the alias
attribute in C is that the alias has the same size as the aliasee. However
we can re-introduce adding the size on the alias when the aliasee does not,
from a source code or object perspective, exist as a discrete entity. This
happens when the aliasee is not a symbol, or when that symbol is private.
Differential Revision: http://reviews.llvm.org/D11943
llvm-svn: 244752
Other objects can never reference the MergedGlobals symbol so external linkage
is never needed. Using private instead of internal linkage means the object is
more similar to what it looks like when global merging is not enabled, with
the only difference being that the merged variables are addressed indirectly
relative to the start of the section they are in.
Also add aliases for merged variables with internal linkage, as this also makes
the object be more like what it is when they are not merged.
Differential Revision: http://reviews.llvm.org/D11942
llvm-svn: 244615
I looked into adding a warning / error for this to FileCheck, but there doesn't
seem to be a good way to avoid it triggering on the instances of it in RUN lines.
llvm-svn: 244481
Summary:
Port the ReconstructShuffle function from AArch64 to ARM
to handle mismatched incoming types in the BUILD_VECTOR
node.
This fixes an outstanding FIXME in the ReconstructShuffle
code.
Reviewers: t.p.northover, rengolin
Subscribers: aemerson, llvm-commits, rengolin
Differential Revision: http://reviews.llvm.org/D11720
llvm-svn: 244314
points.
There is an infinite loop that can occur in Shrink Wrapping while searching
for the Save/Restore points.
Part of this search checks whether the save/restore points are located in
different loop nests and if so, uses the (post) dominator trees to find the
immediate (post) dominator blocks. However, if the current block does not have
any immediate (post) dominators then this search will result in an infinite
loop. This can occur in code containing an infinite loop.
The modification checks whether the immediate (post) dominator is different from
the current save/restore block. If it is not, then the search terminates and the
current location is not considered as a valid save/restore point for shrink wrapping.
Phabricator: http://reviews.llvm.org/D11607
llvm-svn: 244247
return StringSwitch<int>(Flags)
.Case("g", 0x1)
.Case("nzcvq", 0x2)
.Case("nzcvqg", 0x3)
.Default(-1);
...
// The _g and _nzcvqg versions are only valid if the DSP extension is
// available.
if (!Subtarget->hasThumb2DSP() && (Mask & 0x2))
return -1;
ARMARM confirms that the comment is right, and the code was wrong.
llvm-svn: 244029
This adds the software division routines for the Windows RTABI. These are not
expected to be used often though as most modern Windows ARM capable targets
support hardware division. In the case that the target CPU doesnt support
hardware division, this will be the fallback.
llvm-svn: 243952
Since r241097, `DIBuilder` has only created distinct `DICompileUnit`s.
The backend is liable to start relying on that (if it hasn't already),
so make uniquable `DICompileUnit`s illegal and automatically upgrade old
bitcode. This is a nice cleanup, since we can remove an unnecessary
`DenseSet` (and the associated uniquing info) from `LLVMContextImpl`.
Almost all the testcases were updated with this script:
git grep -e '= !DICompileUnit' -l -- test |
grep -v test/Bitcode |
xargs sed -i '' -e 's,= !DICompileUnit,= distinct !DICompileUnit,'
I imagine something similar should work for out-of-tree testcases.
llvm-svn: 243885
This is necessary for WatchOS support, where the compact unwind format assumes
this kind of layout. For now we only want this on Swift-like CPUs though, where
it's been the Xcode behaviour for ages. Also, since it can expand the prologue
we don't want it at -Oz.
llvm-svn: 243884
Enabling merging of extern globals appears to be generally either beneficial or
harmless. On some benchmarks suites (on Cortex-M4F, Cortex-A9, and Cortex-A57)
it gives improvements in the 1-5% range, but in the rest the overall effect is
zero.
Differential Revision: http://reviews.llvm.org/D10966
llvm-svn: 243874
In http://reviews.llvm.org/rL215382, IT forming was made more conservative under
the belief that a flag-setting instruction was unpredictable inside an IT block on ARMv6M.
But actually, ARMv6M doesn't even support IT blocks so that's impossible. In the ARMARM for
v7M, v7AR and v8AR it states that the semantics of such an instruction changes inside an
IT block - it doesn't set the flags. So actually it is fine to use one inside an IT block
as long as the flags register is dead afterwards.
This gives significant performance improvements in a variety of MPEG based workloads.
Differential revision: http://reviews.llvm.org/D11680
llvm-svn: 243869
Remove the fake `DW_TAG_auto_variable` and `DW_TAG_arg_variable` tags,
using `DW_TAG_variable` in their place Stop exposing the `tag:` field at
all in the assembly format for `DILocalVariable`.
Most of the testcase updates were generated by the following sed script:
find test/ -name "*.ll" -o -name "*.mir" |
xargs grep -l 'DILocalVariable' |
xargs sed -i '' \
-e 's/tag: DW_TAG_arg_variable, //' \
-e 's/tag: DW_TAG_auto_variable, //'
There were only a handful of tests in `test/Assembly` that I needed to
update by hand.
(Note: a follow-up could change `DILocalVariable::DILocalVariable()` to
set the tag to `DW_TAG_formal_parameter` instead of `DW_TAG_variable`
(as appropriate), instead of having that logic magically in the backend
in `DbgVariable`. I've added a FIXME to that effect.)
llvm-svn: 243774
For a modulo (reminder) operation,
clang -target armv7-none-linux-gnueabi generates "__modsi3"
clang -target armv7-none-eabi generates "__aeabi_idivmod"
clang -target armv7-linux-androideabi generates "__modsi3"
Android bionic libc doesn't provide a __modsi3, instead it provides a
"__aeabi_idivmod". This patch fixes the LLVM ARMISelLowering to generate
the correct call when ever there is a modulo operation.
Differential Revision: http://reviews.llvm.org/D11661
llvm-svn: 243717
This commit defines subtarget feature strict-align and uses it instead of
cl::opt -arm-strict-align to decide whether strict alignment should be
forced. Also, remove the logic that was checking the OS and architecture
as clang is now responsible for setting strict-align based on the command
line options specified and the target architecute and OS.
rdar://problem/21529937
http://reviews.llvm.org/D11470
llvm-svn: 243493
The 'common' section TLS is not implemented.
Current C/C++ TLS variables are not placed in common section.
DWARF debug info to get the address of TLS variables is not generated yet.
clang and driver changes in http://reviews.llvm.org/D10524
Added -femulated-tls flag to select the emulated TLS model,
which will be used for old targets like Android that do not
support ELF TLS models.
Added TargetLowering::LowerToTLSEmulatedModel as a target-independent
function to convert a SDNode of TLS variable address to a function call
to __emutls_get_address.
Added into lib/Target/*/*ISelLowering.cpp to call LowerToTLSEmulatedModel
for TLSModel::Emulated. Although all targets supporting ELF TLS models are
enhanced, emulated TLS model has been tested only for Android ELF targets.
Modified AsmPrinter.cpp to print the emutls_v.* and emutls_t.* variables for
emulated TLS variables.
Modified DwarfCompileUnit.cpp to skip some DIE for emulated TLS variabls.
TODO: Add proper DIE for emulated TLS variables.
Added new unit tests with emulated TLS.
Differential Revision: http://reviews.llvm.org/D10522
llvm-svn: 243438
Add a verifier check that `DILocalVariable`s of tag
`DW_TAG_arg_variable` always have a non-zero 'arg:' field, and those of
tag `DW_TAG_auto_variable` always have a zero 'arg:' field. These are
the only configurations that are properly understood by the backend.
(Also, fix the bad examples in LangRef and test/Assembler, and fix the
bug in Kaleidoscope Ch8.)
A large number of testcases seem to have bitrotted their way forward
from some ancient version of the debug info hierarchy that didn't have
`arg:` parameters. If you have out-of-tree testcases that start failing
in the verifier and you don't care enough to get the `arg:` right, you
may have some luck just calling:
sed -e 's/, arg: 0/, arg: 1/'
or some such, but I hand-updated the ones in tree.
llvm-svn: 243183
Some shufflevectors are currently being incorrectly lowered in the AArch32
backend as the existing checks for detecting the NEON operations from the
shufflevector instruction expects the shuffle mask and the vector operands to be
of the same length.
This is not always the case as the mask may be twice as long as the operand;
here only the lower half of the shufflemask gets checked, so provided the lower
half of the shufflemask looks like a vector transpose (or even is just all -1
for undef) then the intrinsics may get incorrectly lowered into a vector
transpose (VTRN) instruction.
This patch fixes this by accommodating for both cases and adds regression tests.
Differential Revision: http://reviews.llvm.org/D11407
llvm-svn: 243103
is an immediate, in this check the value is negated and stored in and int64_t.
The value can be -2^63 yet the result cannot be stored in an int64_t and this
gives some undefined behaviour causing failures. The negation is only necessary
when the values is within a certain range and so it should not need to negate
-2^63, this patch introduces this and also a regression test.
Differential Revision: http://reviews.llvm.org/D11408
llvm-svn: 243100
whether register r9 should be reserved.
This recommits r242737, which broke bots because the number of subtarget
features went over the limit of 64.
This change is needed because we cannot use a backend option to set
cl::opt "arm-reserve-r9" when doing LTO.
Out-of-tree projects currently using cl::opt option "-arm-reserve-r9" to
reserve r9 should make changes to add subtarget feature "reserve-r9" to
the IR.
rdar://problem/21529937
Differential Revision: http://reviews.llvm.org/D11320
llvm-svn: 242756
Re-apply of r241928 which had to be reverted because of the r241926
revert.
This commit factors out common code from MergeBaseUpdateLoadStore() and
MergeBaseUpdateLSMultiple() and introduces a new function
MergeBaseUpdateLSDouble() which merges adds/subs preceding/following a
strd/ldrd instruction into an strd/ldrd instruction with writeback where
possible.
Differential Revision: http://reviews.llvm.org/D10676
llvm-svn: 242743
Re-apply r241926 with an additional check that r13 and r15 are not used
for LDRD/STRD. See http://llvm.org/PR24190. This also already includes
the fix from r241951.
Differential Revision: http://reviews.llvm.org/D10623
llvm-svn: 242742
whether register r9 should be reserved.
This change is needed because we cannot use a backend option to set
cl::opt "arm-reserve-r9" when doing LTO.
Out-of-tree projects currently using cl::opt option "-arm-reserve-r9" to
reserve r9 should make changes to add subtarget feature "reserve-r9" to
the IR.
rdar://problem/21529937
Differential Revision: http://reviews.llvm.org/D11320
llvm-svn: 242737
This is the first step toward supporting shrink-wrapping for this target.
The changes could be summarized by these items:
- Expand the tail-call return as part of the expand pseudo pass.
- Get rid of the assumptions that the epilogue is the exit block:
* Do not assume which registers are free in the epilogue. (This indirectly
improve the lowering of the code for the segmented stacks, see the test
cases.)
* Take into account that the basic block can be empty.
Related to <rdar://problem/20821730>
llvm-svn: 242714
Reapply r242500 now that the swift schedmodel includes LDRLIT.
This is mostly done to disable the PostRAScheduler which optimizes for
instruction latencies which isn't a good fit for out-of-order
architectures. This also allows to leave out the itinerary table in
swift in favor of the SchedModel ones.
This change leads to performance improvements/regressions by as much as
10% in some benchmarks, in fact we loose 0.4% performance over the
llvm-testsuite for reasons that appear to be unknown or out of the
compilers control. rdar://20803802 documents the investigation of
these effects.
While it is probably a good idea to perform the same switch for the
other ARM out-of-order CPUs, I limited this change to swift as I cannot
perform the benchmark verification on the other CPUs.
Differential Revision: http://reviews.llvm.org/D10513
llvm-svn: 242588
This is mainly for the benefit of GlobalMerge, so that an alias into a
MergedGlobals variable has the same size as the original non-merged
variable.
Differential Revision: http://reviews.llvm.org/D10837
llvm-svn: 242520
This is mostly done to disable the PostRAScheduler which optimizes for
instruction latencies which isn't a good fit for out-of-order
architectures. This also allows to leave out the itinerary table in
swift in favor of the SchedModel ones.
This change leads to performance improvements/regressions by as much as
10% in some benchmarks, in fact we loose 0.4% performance over the
llvm-testsuite for reasons that appear to be unknown or out of the
compilers control. rdar://20803802 documents the investigation of
these effects.
While it is probably a good idea to perform the same switch for the
other ARM out-of-order CPUs, I limited this change to swift as I cannot
perform the benchmark verification on the other CPUs.
Differential Revision: http://reviews.llvm.org/D10513
llvm-svn: 242500
llvm.eh.sjlj.setjmp was used as part of the SjLj exception handling
style but is also used in clang to implement __builtin_setjmp. The ARM
backend needs to output additional dispatch tables for the SjLj
exception handling style, these tables however can't be emitted if
llvm.eh.sjlj.setjmp is simply used for __builtin_setjmp and no actual
landing pad blocks exist.
To solve this issue a new llvm.eh.sjlj.setup_dispatch intrinsic is
introduced which is used instead of llvm.eh.sjlj.setjmp in the SjLj
exception handling lowering, so we can differentiate between the case
where we actually need to setup a dispatch table and the case where we
just need the __builtin_setjmp semantic.
Differential Revision: http://reviews.llvm.org/D9313
llvm-svn: 242481
This reverts commit r242300.
This is causing buildbot failures which we are investigating.
I'll reapply once we know whats going on, but for now want to
get the bots green.
llvm-svn: 242428
pairs for 32-bit immediates.
This change is needed to avoid emitting movt/movw pairs when doing LTO
and do so on a per-function basis.
Out-of-tree projects currently using cl::opt option -arm-use-movt=0 or
false to avoid emitting movt/movw pairs should make changes to add
subtarget feature "+no-movt" (see the changes made to clang in r242368).
rdar://problem/21529937
Differential Revision: http://reviews.llvm.org/D11026
llvm-svn: 242369
These were the cause of a verifier error when building 7zip with
-verify-machineinstrs. Running 'make check' with the verifier
triggered the same error on the test here so i've updated the test
to run the verifier on one of its runs instead of adding a new one.
While looking at this code, there was a stale comment that these
instructions were only used for disassembly. This probably used to
be the case, but they are now used in the 'ARM load / store optimization pass' too.
llvm-svn: 242300
The ones committed were orthogonal to the change and would have passed before
that revision. What it *did* do was prevent an assertion failure when
generating object files.
llvm-svn: 242166
This changes TargetFrameLowering::processFunctionBeforeCalleeSavedScan():
- Rename the function to determineCalleeSaves()
- Pass a bitset of callee saved registers by reference, thus avoiding
the function-global PhysRegUsed bitset in MachineRegisterInfo.
- Without PhysRegUsed the implementation is fine tuned to not save
physcial registers which are only read but never modified.
Related to rdar://21539507
Differential Revision: http://reviews.llvm.org/D10909
llvm-svn: 242165
The 64/128-bit vector types are legal if NEON instructions are
available. However, there was no matching patterns for @llvm.cttz.*()
intrinsics and result in fatal error.
This commit fixes the problem by lowering cttz to:
a. ctpop((x & -x) - 1)
b. width - ctlz(x & -x) - 1
llvm-svn: 242037
Register r12 ('ip') is used by GCC for this purpose
and hence is used here. As discussed on the GCC mailing
list, the register choice is an ABI issue and so
choosing the same register as GCC means
__builtin_call_with_static_chain is compatible.
A similar patch has just gone in the AArch64 backend,
so this is just the ARM counterpart, following the same
discussion.
Patch by Stephen Cross.
llvm-svn: 241996
This commit factors out common code from MergeBaseUpdateLoadStore() and
MergeBaseUpdateLSMultiple() and introduces a new function
MergeBaseUpdateLSDouble() which merges adds/subs preceding/following a
strd/ldrd instruction into an strd/ldrd instruction with writeback where
possible.
Differential Revision: http://reviews.llvm.org/D10676
llvm-svn: 241928
This improves the logic in several ways and is a preparation for
followup patches:
- First perform an analysis and create a list of merge candidates, then
transform. This simplifies the code in that you have don't have to
care to much anymore that you may be holding iterators to
MachineInstrs that get removed.
- Analyze/Transform basic blocks in reverse order. This allows to use
LivePhysRegs to find free registers instead of the RegisterScavenger.
The RegisterScavenger will become less precise in the future as it
relies on the deprecated kill-flags.
- Return the newly created node in MergeOps so there's no need to look
around in the schedule to find it.
- Rename some MBBI iterators to InsertBefore to make their role clear.
- General code cleanup.
Differential Revision: http://reviews.llvm.org/D10140
llvm-svn: 241920
This commit changes the target arch to fix the test case commited in r241566
that was failing on ninja-x64-msvc-RA-centos6. Also add checks to make sure
the callee's address is loaded to blx's operand.
llvm-svn: 241588
be emitted.
This is needed to enable ARM long calls for LTO and enable and disable it on a
per-function basis.
Out-of-tree projects currently using EnableARMLongCalls to emit long calls
should start passing "+long-calls" to the feature string (see the changes made
to clang in r241565).
rdar://problem/21529937
Differential Revision: http://reviews.llvm.org/D9364
llvm-svn: 241566
This commit changes normal isel and fast isel to read the user-defined trap
function name from function attribute "trap-func-name" attached to llvm.trap or
llvm.debugtrap instead of from TargetOptions::TrapFuncName. This is needed to
use clang's command line option "-ftrap-function" for LTO and enable changing
the trap function name on a per-call-site basis.
Out-of-tree projects currently using TargetOptions::TrapFuncName to specify the
trap function name should attach attribute "trap-func-name" to the call sites
of llvm.trap and llvm.debugtrap instead.
rdar://problem/21225723
Differential Revision: http://reviews.llvm.org/D10832
llvm-svn: 241305
When the store sequence being combined actually stores the base register, we
should not mark it as killed until the end.
rdar://21504262
llvm-svn: 241003
Some of the the permissible ARM -mfpu options, which are supported in GCC,
are currently not present in llvm/clang.This patch adds the options:
'neon-fp16', 'vfpv3-fp16', 'vfpv3-d16-fp16', 'vfpv3xd' and 'vfpv3xd-fp16.
These are related to half-precision floating-point and single precision.
Reviewers: rengolin, ranjeet.singh
Subscribers: llvm-commits
Differential Revision: http://reviews.llvm.org/D10645
llvm-svn: 240930
This patch fixes the error in ARM.td which stated that Cortex-R5
floating point unit can do only single precision, when it can do double as well.
Reviewers: rengolin
Subscribers: llvm-commits
Differential Revision: http://reviews.llvm.org/D10769
llvm-svn: 240799
Cortex-R4F TRM states that fpu supports both single and double precision.
This patch corrects the information in ARM.td file and corresponding test.
Reviewers: rengolin
Subscribers: llvm-commits
Differential Revision: http://reviews.llvm.org/D10763
llvm-svn: 240776
Currently, we canonicalize shuffles that produce a result larger than
their operands with:
shuffle(concat(v1, undef), concat(v2, undef))
->
shuffle(concat(v1, v2), undef)
because we can access quad vectors (see PerformVECTOR_SHUFFLECombine).
This is useful in the general case, but there are special cases where
native shuffles produce larger results: the two-result ops.
We can look through the concat when lowering them:
shuffle(concat(v1, v2), undef)
->
concat(VZIP(v1, v2):0, :1)
This lets us generate the native shuffles instead of scalarizing to
dozens of VMOVs.
Differential Revision: http://reviews.llvm.org/D10424
llvm-svn: 240118
The personality routine currently lives in the LandingPadInst.
This isn't desirable because:
- All LandingPadInsts in the same function must have the same
personality routine. This means that each LandingPadInst beyond the
first has an operand which produces no additional information.
- There is ongoing work to introduce EH IR constructs other than
LandingPadInst. Moving the personality routine off of any one
particular Instruction and onto the parent function seems a lot better
than have N different places a personality function can sneak onto an
exceptional function.
Differential Revision: http://reviews.llvm.org/D10429
llvm-svn: 239940
ARMTargetParser::getFPUFeatures should disable fp16 whenever it
disables vfp4, as otherwise something like -mcpu=cortex-a7 -mfpu=none
leaves us with fp16 enabled (though the only effect that will have is
a wrong build attribute).
Differential Revision: http://reviews.llvm.org/D10397
llvm-svn: 239599
that was resetting it.
Remove the uses of DisableTailCalls in subclasses of TargetLowering and use
the value of function attribute "disable-tail-calls" instead. Also,
unconditionally add pass TailCallElim to the pipeline and check the function
attribute at the start of runOnFunction to disable the pass on a per-function
basis.
This is part of the work to remove TargetMachine::resetTargetOptions, and since
DisableTailCalls was the last non-fast-math option that was being reset in that
function, we should be able to remove the function entirely after the work to
propagate IR-level fast-math flags to DAG nodes is completed.
Out-of-tree users should remove the uses of DisableTailCalls and make changes
to attach attribute "disable-tail-calls"="true" or "false" to the functions in
the IR.
rdar://problem/13752163
Differential Revision: http://reviews.llvm.org/D10099
llvm-svn: 239427
on a per-function basis.
Previously some of the passes were conditionally added to ARM's pass pipeline
based on the target machine's subtarget. This patch makes changes to add those
passes unconditionally and execute them conditonally based on the predicate
functor passed to the pass constructors. This enables running different sets of
passes for different functions in the module.
rdar://problem/20542263
Differential Revision: http://reviews.llvm.org/D8717
llvm-svn: 239325
These are added mainly for the benefit of clang, but this also means that they
are now allowed in .fpu directives and we emit the correct .fpu directive when
single-precision-only is used.
Differential Revision: http://reviews.llvm.org/D10238
llvm-svn: 239151
The existing code would unnecessarily break LDRD/STRD apart with
non-adjacent registers, on thumb2 this is not necessary.
Ideally on thumb2 we shouldn't match for ldrd/strd pre-regalloc anymore
as there is not reason to set register hints anymore, changing that is
something for a future patch however.
Differential Revision: http://reviews.llvm.org/D9694
Recommiting after the revert in r238821, the buildbot still failed with
the patch removed so there seems to be another reason for the breakage.
llvm-svn: 238935
This reverts commit r238795, as it broke the Thumb2 self-hosting buildbot.
Since self-hosting issues with Clang are hard to investigate, I'm taking the
liberty to revert now, so we can investigate it offline.
llvm-svn: 238821
The existing code would unnecessarily break LDRD/STRD apart with
non-adjacent registers, on thumb2 this is not necessary.
Ideally on thumb2 we shouldn't match for ldrd/strd pre-regalloc anymore
as there is not reason to set register hints anymore, changing that is
something for a future patch however.
Differential Revision: http://reviews.llvm.org/D9694
llvm-svn: 238795
The original version didn't properly account for the base register
being modified before the final jump, so caused miscompilations in
Chromium and LLVM. I've fixed this and tested with an LLVM self-host
(I don't have the means to build & test Chromium).
The general idea remains the same: in pathological cases jump tables
can be too far away from the instructions referencing them (like other
constants) so they need to be movable.
Should fix PR23627.
llvm-svn: 238680
This is part of the work to remove TargetMachine::resetTargetOptions.
In this patch, instead of updating global variable NoFramePointerElim in
resetTargetOptions, its use in DisableFramePointerElim is replaced with a call
to TargetFrameLowering::noFramePointerElim. This function determines on a
per-function basis if frame pointer elimination should be disabled.
There is no change in functionality except that cl:opt option "disable-fp-elim"
can now override function attribute "no-frame-pointer-elim".
llvm-svn: 238080
Ideally this is going to be and LLVM IR pass (shared, among others
with AArch64), but for the time being just enable it if consumers
ask us for optimization and not unconditionally.
Discussed with Tim Northover on IRC.
llvm-svn: 237837
Previously, they were forced to immediately follow the actual branch
instruction. This was usually OK (the LEAs actually accessing them got emitted
nearby, and weren't usually separated much afterwards). Unfortunately, a
sufficiently nasty phi elimination dumps many instructions right before the
basic block terminator, and this can increase the range too much.
This patch frees them up to be placed as usual by the constant islands pass,
and consequently has to slightly modify the form of TBB/TBH tables to refer to
a PC-relative label at the final jump. The other jump table formats were
already position-independent.
rdar://20813304
llvm-svn: 237590
This patch implements LLVM support for the ACLE special register intrinsics in
section 10.1, __arm_{w,r}sr{,p,64}.
This patch is intended to lower the read/write_register instrinsics, used to
implement the special register intrinsics in the clang patch for special
register intrinsics (see http://reviews.llvm.org/D9697), to ARM specific
instructions MRC,MCR,MSR etc. to allow reading an writing of coprocessor
registers in AArch32 and AArch64. This is done by inspecting the register
string passed to the intrinsic and then lowering to the appropriate
instruction.
Patch by Luke Cheeseman.
Differential Revision: http://reviews.llvm.org/D9699
llvm-svn: 237579
Other targets probably should as well. Since r237161, compiler-rt has
both, but I don't see why anything other than gnueabi would use a
gnueabi naming scheme.
llvm-svn: 237324
AEABI defines aligned variants of memcpy etc. that can be faster than
the default version due to not having to do alignment checks. When
emitting target code for these functions make use of these aligned
variants if possible. Also convert memset to memclr if possible.
Differential Revision: http://reviews.llvm.org/D8060
llvm-svn: 237127
to use the information in the module rather than TargetOptions.
We've had and clang has used the use-soft-float attribute for some
time now so have the backends set a subtarget feature based on
a particular function now that subtargets are created based on
functions and function attributes.
For the one middle end soft float check go ahead and create
an overloadable TargetLowering::useSoftFloat function that
just checks the TargetSubtargetInfo in all cases.
Also remove the command line option that hard codes whether or
not soft-float is set by using the attribute for all of the
target specific test cases - for the generic just go ahead and
add the attribute in the one case that showed up.
llvm-svn: 237079
When emitting something like 'add x, 1000' if we remat the 1000 then we should be able to
mark the vreg containing 1000 as killed. Given that we go bottom up in fast-isel, a later
use of 1000 will be higher up in the BB and won't kill it, or be impacted by the lower kill.
However, rematerialised constant expressions aren't generated bottom up. The local value save area
grows downwards. This means that if you remat 2 constant expressions which both use 1000 then the
first will kill it, then the second, which is *lower* in the BB will read a killed register.
This is the case in the attached test where the 2 GEPs both need to generate 'add x, 6680' for the constant offset.
Note that this commit only makes kill flag generation conservative. There's nothing else obviously wrong with
the local value save area growing downwards, and in fact it needs to for handling arbitrarily complex constant expressions.
However, it would be nice if there was a solution which would let us generate more accurate kill flags, or just kill flags completely.
llvm-svn: 236922
The code that builds the dependence graph assumes that two PseudoSourceValues
don't alias. In a tail calling function two FixedStackObjects might refer to the
same location. Worse 'immutable' fixed stack objects like function arguments are
not immutable and will be clobbered.
Change this so that a load from a FixedStackObject is not invariant in a tail
calling function and don't return a PseudoSourceValue for an instruction in tail
calling functions when building the dependence graph so that we handle function
arguments conservatively.
Fix for PR23459.
rdar://20740035
llvm-svn: 236916
When selecting an extract instruction, we don't actually generate code but instead work out which register we are reading, and rewrite uses of the extract def to the source register. This is done via updateValueMap,.
However, its possible that the source register we are rewriting *to* to also have uses. If those uses are after a kill of the value we are rewriting *from* then we have uses after a kill and the verifier fails.
This code checks for the case where the to register is also used, and if so it clears all kill on the from register. This is conservative, but better that always clearing kills on the from register.
llvm-svn: 236897
If we duplicate an instruction then we must also clear kill flags on any uses we rewrite.
Otherwise we might be killing a register which was used in other BBs.
For example, here the entry BB ended up with these instructions, the ADD having been tail duplicated.
%vreg24<def> = t2ADDri %vreg10<kill>, 1, pred:14, pred:%noreg, opt:%noreg; GPRnopc:%vreg24 rGPR:%vreg10
%vreg22<def> = COPY %vreg10; GPR:%vreg22 rGPR:%vreg10
The copy here is inserted after the add and so needs vreg10 to be live.
llvm-svn: 236782
We had code such as this:
r2 = ...
t2Bcc
label1:
ldr ... r2
label2;
return r2<dead, def>
The if converter was transforming this to
r2<def> = ...
return [pred] r2<dead,def>
ldr <r2, kill>
return
which fails the machine verifier because the ldr now reads from a dead def.
The fix here detects dead defs in stepForward and passes them back to the caller in the clobbers list. The caller then clears the dead flag from the def is the value is live.
llvm-svn: 236660
If called twice in the same BB on the same constant, FastISel::fastEmit_ri_ was marking the materialized vreg as killed on each use, instead of only the last use.
Change this to only mark the last use as killed by making earlier uses check if the vreg is already used elsewhere.
llvm-svn: 236650
With neon enabled, we reach SelectBinaryFPOp and are able to get registers for a <2 x double> add.
However, we shouldn't actually attempt arithmetic on it as ARMIselLowering says "v2f64 is legal so that QR subregs can be extracted as f64 elements, but neither Neon nor VFP support any arithmetic operations on it."
This commit disables SelectBinaryFPOp for any vector types. There's already a FIXME to try handle neon. Doing so would require fixing this conditional which isn't safe for vectors 'VT == MVT::f64 || VT == MVT::i64'
llvm-svn: 236609
Since r234249, i1 are sext instead of zext; because of that, doing
"CMP rN, #0; IT EQ/NE" isn't correct anymore.
"TST #1" is the conservatively correct alternative - the tradeoff being
that it doesn't have a 16-bit encoding -, so use that instead.
llvm-svn: 236569
Note, this is a recommit of r236515 after fixing an error in r236514. The buildbot ran fast enough that it picked up r236514 prior to r236515 and threw an error. r236515 itself ran 'make check' without errors.
Original commit message follows:
A regmask (typically seen on a call) clobbers the set of registers it lists. The IfConverter, in UpdatePredRedefs, was handling register defs, but not regmasks.
These are slightly different to a def in that we need to add both an implicit use and def to appease the machine verifier. Otherwise, uses after the if converted call could think they are reading an undefined register.
Reviewed by Matthias Braun and Quentin Colombet.
llvm-svn: 236550
This reverts commit b27413cbfd78d959c18e713bfa271fb69e6b3303 (ie r236515).
This is to get the bots green while i investigate the failures.
llvm-svn: 236517
A regmask (typically seen on a call) clobbers the set of registers it lists. The IfConverter, in UpdatePredRedefs, was handling register defs, but not regmasks.
These are slightly different to a def in that we need to add both an implicit use and def to appease the machine verifier. Otherwise, uses after the if converted call could think they are reading an undefined register.
Reviewed by Matthias Braun and Quentin Colombet.
llvm-svn: 236515
Functions with jump tables need an alignment of 4 because they use the ADR
instruction, which aligns the PC to 4 bytes before adding an offset.
Differential Revision: http://reviews.llvm.org/D9424
llvm-svn: 236327
If we move an instruction from one block down to a MOVC and predicate it,
then the original instruction could be moved in to a loop. In this case,
its invalid for any kill flags to remain on there.
Fails with -verfy-machineinstrs.
rdar://problem/20752113
llvm-svn: 236290
When commuting a thumb instruction in the size reduction pass, thumb
instructions are represented as a bundle and so some operands may be marked
as internal. The internal flag has to move with the operand when commuting.
This test is sensitive to register allocation so can't specifically check that
this error was happening, but so long as it continues to pass with -verify then
hopefully its still ok.
rdar://problem/20752113
llvm-svn: 236282
The expansion for t2ABS was always setting the kill flag on the rsb instruction.
It should instead only be set on rsb if it was set on the original ABS instruction.
rdar://problem/20752113
llvm-svn: 236272
temporary.
Because of that:
1. The machine verifier was complaining on such code.
2. The generate code worked just because the thumb reduction size pass fixed the
opcode.
rdar://problem/20749824
llvm-svn: 236247
Finish off PR23080 by renaming the debug info IR constructs from `MD*`
to `DI*`. The last of the `DIDescriptor` classes were deleted in
r235356, and the last of the related typedefs removed in r235413, so
this has all baked for about a week.
Note: If you have out-of-tree code (like a frontend), I recommend that
you get everything compiling and tests passing with the *previous*
commit before updating to this one. It'll be easier to keep track of
what code is using the `DIDescriptor` hierarchy and what you've already
updated, and I think you're extremely unlikely to insert bugs. YMMV of
course.
Back to *this* commit: I did this using the rename-md-di-nodes.sh
upgrade script I've attached to PR23080 (both code and testcases) and
filtered through clang-format-diff.py. I edited the tests for
test/Assembler/invalid-generic-debug-node-*.ll by hand since the columns
were off-by-three. It should work on your out-of-tree testcases (and
code, if you've followed the advice in the previous paragraph).
Some of the tests are in badly named files now (e.g.,
test/Assembler/invalid-mdcompositetype-missing-tag.ll should be
'dicompositetype'); I'll come back and move the files in a follow-up
commit.
llvm-svn: 236120
We were trying to look through COPY instructions, but only to the next
instruction in a BB and incorrectly anyway. The cases where that would actually
be a good idea are rare enough (and not even tested!) that it's not worth
trying to get right.
rdar://20721342
llvm-svn: 236050
Previously, the code would try to put a fall-through case last,
even if that meant moving a case with much higher branch weight
further down the chain.
Ordering by branch weight is most important, putting a fall-through
block last is secondary.
llvm-svn: 235942
In particular, this preserves the kill flag, which allows the Thumb2 cbn?z
optimization to be applied in cases where a branch has been re-created after
the live variables analysis pass, e.g. by the machine block placement pass.
This appears to be low risk; a number of other targets seem to already be
doing something similar, e.g. AArch64, PowerPC.
Differential Revision: http://reviews.llvm.org/D9184
llvm-svn: 235639
This makes it more likely that we can use the 16-bit push and pop instructions
on Thumb-2, saving around 4 bytes per function.
Differential Revision: http://reviews.llvm.org/D9165
llvm-svn: 235637
This appears to have been introduced back in r76698 as part of an unrelated
change. I can find no official ARM documentation stating that Thumb-2 functions
require 4-byte alignment; in fact, ARM documentation appears to contradict
this (see, e.g., ARM Architecture Reference Manual Thumb-2 Supplement,
section 2.6.1: "Thumb-2 enforces 16-bit alignment on all instructions.").
Also remove code that sets alignment for ARM functions, which is redundant
with code in the MachineFunction constructor, and remove the hidden
-arm-align-constant-islands flag, which has been enabled by default since
r146739 (Dec 2011) and has probably received sufficient testing by now.
Differential Revision: http://reviews.llvm.org/D9138
llvm-svn: 235636
Third time's the charm. The previous commit was reverted as a
reverse for-loop in SelectionDAGBuilder::lowerWorkItem did 'I--'
on an iterator at the beginning of a vector, causing asserts
when using debugging iterators. This commit fixes that.
llvm-svn: 235608
This is a re-commit of r235101, which also fixes the problems with the previous patch:
- Switches with only a default case and non-fallthrough were handled incorrectly
- The previous patch tickled a bug in PowerPC Early-Return Creation which is fixed here.
> This is a major rewrite of the SelectionDAG switch lowering. The previous code
> would lower switches as a binary tre, discovering clusters of cases
> suitable for lowering by jump tables or bit tests as it went along. To increase
> the likelihood of finding jump tables, the binary tree pivot was selected to
> maximize case density on both sides of the pivot.
>
> By not selecting the pivot in the middle, the binary trees would not always
> be balanced, leading to performance problems in the generated code.
>
> This patch rewrites the lowering to search for clusters of cases
> suitable for jump tables or bit tests first, and then builds the binary
> tree around those clusters. This way, the binary tree will always be balanced.
>
> This has the added benefit of decoupling the different aspects of the lowering:
> tree building and jump table or bit tests finding are now easier to tweak
> separately.
>
> For example, this will enable us to balance the tree based on profile info
> in the future.
>
> The algorithm for finding jump tables is quadratic, whereas the previous algorithm
> was O(n log n) for common cases, and quadratic only in the worst-case. This
> doesn't seem to be major problem in practice, e.g. compiling a file consisting
> of a 10k-case switch was only 30% slower, and such large switches should be rare
> in practice. Compiling e.g. gcc.c showed no compile-time difference. If this
> does turn out to be a problem, we could limit the search space of the algorithm.
>
> This commit also disables all optimizations during switch lowering in -O0.
>
> Differential Revision: http://reviews.llvm.org/D8649
llvm-svn: 235560
Summary:
In the f16-promote test, make the checks for native conversion instructions
similar to the libcall checks:
- Remove hard coded register names
- Do not check exact instruction sequences.
This fixes test flakiness due to non-determinism in instruction
scheduling and register allocation. I also fixed a few minor things in
the CHECK-LIBCALL checks.
I'll try to find a way to check that unnecessary loads, stores, or
conversions don't happen.
Reviewers: mzolotukhin, srhines, ab
Subscribers: llvm-commits
Differential Revision: http://reviews.llvm.org/D9112
llvm-svn: 235363
Instead of merging everything together, look at the users of
GlobalVariables, and try to group them by function, to create
sets of globals used "together".
Using that information, a less-aggressive alternative is to keep merging
everything together *except* globals that are only ever used alone, that
is, those for which it's clearly non-profitable to merge with others.
In my testing, grouping by Function is too aggressive, but grouping by
BasicBlock is too conservative. Anything in-between isn't trivially
available, so stick with Function grouping for now.
cl::opts are added for testing; both enabled by default.
A few of the testcases aren't testing the merging proper, but just
various edge cases when merging does occur. Update them to use the
previous grouping behavior. Also, one of the tests is unrelated to
GlobalMerge; change it accordingly.
While there, switch to r234666' flags rather than the brutal -O3.
Differential Revision: http://reviews.llvm.org/D8070
llvm-svn: 235249
Summary:
This patch adds legalization support to operate on FP16 as a load/store type
and do operations on it as floats.
Tests for ARM are added to test/CodeGen/ARM/fp16-promote.ll
Reviewers: srhines, t.p.northover
Differential Revision: http://reviews.llvm.org/D8755
llvm-svn: 235215
See r230786 and r230794 for similar changes to gep and load
respectively.
Call is a bit different because it often doesn't have a single explicit
type - usually the type is deduced from the arguments, and just the
return type is explicit. In those cases there's no need to change the
IR.
When that's not the case, the IR usually contains the pointer type of
the first operand - but since typed pointers are going away, that
representation is insufficient so I'm just stripping the "pointerness"
of the explicit type away.
This does make the IR a bit weird - it /sort of/ reads like the type of
the first operand: "call void () %x(" but %x is actually of type "void
()*" and will eventually be just of type "ptr". But this seems not too
bad and I don't think it would benefit from repeating the type
("void (), void () * %x(" and then eventually "void (), ptr %x(") as has
been done with gep and load.
This also has a side benefit: since the explicit type is no longer a
pointer, there's no ambiguity between an explicit type and a function
that returns a function pointer. Previously this case needed an explicit
type (eg: a function returning a void() function was written as
"call void () () * @x(" rather than "call void () * @x(" because of the
ambiguity between a function returning a pointer to a void() function
and a function returning void).
No ambiguity means even function pointer return types can just be
written alone, without writing the whole function's type.
This leaves /only/ the varargs case where the explicit type is required.
Given the special type syntax in call instructions, the regex-fu used
for migration was a bit more involved in its own unique way (as every
one of these is) so here it is. Use it in conjunction with the apply.sh
script and associated find/xargs commands I've provided in rr230786 to
migrate your out of tree tests. Do let me know if any of this doesn't
cover your cases & we can iterate on a more general script/regexes to
help others with out of tree tests.
About 9 test cases couldn't be automatically migrated - half of those
were functions returning function pointers, where I just had to manually
delete the function argument types now that we didn't need an explicit
function type there. The other half were typedefs of function types used
in calls - just had to manually drop the * from those.
import fileinput
import sys
import re
pat = re.compile(r'((?:=|:|^|\s)call\s(?:[^@]*?))(\s*$|\s*(?:(?:\[\[[a-zA-Z0-9_]+\]\]|[@%](?:(")?[\\\?@a-zA-Z0-9_.]*?(?(3)"|)|{{.*}}))(?:\(|$)|undef|inttoptr|bitcast|null|asm).*$)')
addrspace_end = re.compile(r"addrspace\(\d+\)\s*\*$")
func_end = re.compile("(?:void.*|\)\s*)\*$")
def conv(match, line):
if not match or re.search(addrspace_end, match.group(1)) or not re.search(func_end, match.group(1)):
return line
return line[:match.start()] + match.group(1)[:match.group(1).rfind('*')].rstrip() + match.group(2) + line[match.end():]
for line in sys.stdin:
sys.stdout.write(conv(re.search(pat, line), line))
llvm-svn: 235145
This is a major rewrite of the SelectionDAG switch lowering. The previous code
would lower switches as a binary tre, discovering clusters of cases
suitable for lowering by jump tables or bit tests as it went along. To increase
the likelihood of finding jump tables, the binary tree pivot was selected to
maximize case density on both sides of the pivot.
By not selecting the pivot in the middle, the binary trees would not always
be balanced, leading to performance problems in the generated code.
This patch rewrites the lowering to search for clusters of cases
suitable for jump tables or bit tests first, and then builds the binary
tree around those clusters. This way, the binary tree will always be balanced.
This has the added benefit of decoupling the different aspects of the lowering:
tree building and jump table or bit tests finding are now easier to tweak
separately.
For example, this will enable us to balance the tree based on profile info
in the future.
The algorithm for finding jump tables is O(n^2), whereas the previous algorithm
was O(n log n) for common cases, and quadratic only in the worst-case. This
doesn't seem to be major problem in practice, e.g. compiling a file consisting
of a 10k-case switch was only 30% slower, and such large switches should be rare
in practice. Compiling e.g. gcc.c showed no compile-time difference. If this
does turn out to be a problem, we could limit the search space of the algorithm.
This commit also disables all optimizations during switch lowering in -O0.
Differential Revision: http://reviews.llvm.org/D8649
llvm-svn: 235101
Remove 'inlinedAt:' from MDLocalVariable. Besides saving some memory
(variables with it seem to be single largest `Metadata` contributer to
memory usage right now in -g -flto builds), this stops optimization and
backend passes from having to change local variables.
The 'inlinedAt:' field was used by the backend in two ways:
1. To tell the backend whether and into what a variable was inlined.
2. To create a unique id for each inlined variable.
Instead, rely on the 'inlinedAt:' field of the intrinsic's `!dbg`
attachment, and change the DWARF backend to use a typedef called
`InlinedVariable` which is `std::pair<MDLocalVariable*, MDLocation*>`.
This `DebugLoc` is already passed reliably through the backend (as
verified by r234021).
This commit removes the check from r234021, but I added a new check
(that will survive) in r235048, and changed the `DIBuilder` API in
r235041 to require a `!dbg` attachment whose 'scope:` is in the same
`MDSubprogram` as the variable's.
If this breaks your out-of-tree testcases, perhaps the script I used
(mdlocalvariable-drop-inlinedat.sh) will help; I'll attach it to PR22778
in a moment.
llvm-svn: 235050
Add missing `!dbg` attachments to `@llvm.dbg.*` intrinsics. I updated
these using a script (add-dbg-to-intrinsics.sh) that I'll attach to
PR22778 for posterity.
llvm-svn: 235040
Many of these predate llvm-readobj. With elf-dump we had to match
a relocation to symbol number and symbol number to symbol name or
section number.
llvm-svn: 235015
This commit makes LLVM not estimate branch probabilities when doing a
single bit bitmask tests.
The code that originally made me discover this is:
if ((a & 0x1) == 0x1) {
..
}
In this case we don't actually have any branch probability information
and should not assume to have any. LLVM transforms this into:
%and = and i32 %a, 1
%tobool = icmp eq i32 %and, 0
So, in this case, the result of a bitwise and is compared against 0,
but nevertheless, we should not assume to have probability
information.
CodeGen/ARM/2013-10-11-select-stalls.ll started failing because the
changed probabilities changed the results of
ARMBaseInstrInfo::isProfitableToIfCvt() and led to an Ifcvt of the
diamond in the test. AFAICT, the test was never meant to test this and
thus changing the test input slightly to not change the probabilities
seems like the best way to preserve the meaning of the test.
llvm-svn: 234979
Fill in the TODO in CodeGenPrepare::OptimizeCallInst so that global
variables that are passed to memory intrinsics are aligned in the same
way that allocas are.
Differential Revision: http://reviews.llvm.org/D8421
llvm-svn: 234735
Currently, there's a single flag, checked by the pass itself.
It can't force-enable the pass (and is on by default), because it
might not even have been created, as that's the targets decision.
Instead, have separate explicit flags, so that the decision is
consistently made in the target.
Keep the flag as a last-resort "force-disable GlobalMerge" for now,
for backwards compatibility.
llvm-svn: 234666
Currently, llvm (backend) doesn't know cortex-r4, even though it is the
default target for armv7r. Using "--target=armv7r-arm-none-eabi" provokes
'cortex-r4' is not a recognized processor for this target' by llvm.
This patch adds support for cortex-r4 and, very closely related, r4f.
llvm-svn: 234486
Because -menable-no-nans causes fcmp conditions to be rewritten
without 'o' or 'u' the recognition code in needs to cope. Also
extended it to handle 'le' and 'ge.
Differential Revision: http://reviews.llvm.org/D8725
llvm-svn: 234421
Summary: Looks like new code from [[ http://reviews.llvm.org/rL222057 | rL222057 ]] doesn't account for early `return` in `ARMFrameLowering::emitPrologue`, which leads to loosing `.cfi_def_cfa_offset` directive for functions without stack frame.
Reviewers: echristo, rengolin, asl, t.p.northover
Reviewed By: t.p.northover
Subscribers: llvm-commits, rengolin, aemerson
Differential Revision: http://reviews.llvm.org/D8606
llvm-svn: 234399
Check that the `MDLocalVariable::getInlinedAt()` in a debug info
intrinsic's variable always matches the `MDLocation::getInlinedAt()` of
its `!dbg` attachment.
The goal here is to get rid of `MDLocalVariable::getInlinedAt()`
entirely (PR22778), since it's expensive and unnecessary, but I'll let
this verifier check bake for a while (a week maybe?) first. I've
updated the testcases that had the wrong value for `inlinedAt:`.
This checks that things are sane in the IR, but currently things go out
of whack in a few places in the backend. I'll follow shortly with
assertions in the backend (with code fixes).
If you have out-of-tree testcases that just started failing, here's how
I updated these ones:
1. The verifier check gives you the basic block, function, instruction,
and relevant metadata arguments (metadata numbering doesn't
necessarily match the source file, unfortunately).
2. Look at the `@llvm.dbg.*()` instruction, and compare the
`inlinedAt:` fields of the variable argument (second `metadata`
argument) and the `!dbg` attachment.
3. Figure out based on the variable `scope:` chain and the functions in
the file whether the variable has been inlined (and into what), so
you can determine which `inlinedAt:` is actually correct. In all of
the in-tree testcases, the `!MDLocation()` was correct and the
`!MDLocalVariable()` was wrong, but YMMV.
4. Duplicate the metadata that you're going to change, and add/drop the
`inlinedAt:` field from one of them. Be careful that the other
references to the same metadata node point at the correct one.
llvm-svn: 234021
Register coalescing can change the target of a RegPair hint to a
physreg, we should not crash on this. This also slightly improved the
way ARMBaseRegisterInfo::updateRegAllocHint() works.
llvm-svn: 233987
it more liberally.
SplitVecOp_TRUNCATE has logic for recursively splitting oversize vectors
that need more than one round of splitting to become legal. There are many
other ISD nodes that could benefit from this logic, so factor it out and
use it for FP_TO_UINT,FP_TO_SINT,SINT_TO_FP,UINT_TO_FP and FTRUNC.
llvm-svn: 233681
Fix debug info in these tests, which started failing with a WIP patch to
verify compile units and types. The problems look like they were all
caused by bitrot. They fell into these categories:
- Using `!{i32 0}` instead of `!{}`.
- Using `!{null}` instead of `!{}`.
- Using `!MDExpression()` instead of `!{}`.
- Using `!8` instead of `!{!8}`.
- `file:` references that pointed at `MDCompileUnit`s instead of the
same `MDFile` as the compile unit.
- `file:` references that were numerically off-by-one or (off-by-ten).
llvm-svn: 233415
"Fix the MachineScheduler's logic for updating ready times for in-order.
Now the scheduler updates a node's ready time as soon as it is
scheduled, before releasing dependent nodes."
This fix was only made in one variant of the ScheduleDAGMI driver.
Francois de Ferriere reported the issue in the other bit of code where
it was also needed.
I never got around to coming up with a test case, but it's an
obvious fix that shouldn't be delayed any longer.
I'll try to refactor this code a little better.
I did verify performance on a wide variety of targets and saw no
negative impact with this fix.
llvm-svn: 233366
Summary:
The ARM backend can use a loop to implement copying byval parameters before
a call. In non-thumb2 mode it uses a constant pool load to materialize the
trip count. For targets that need movt instead (e.g. Native Client), use
the same code as in thumb2 mode to materialize the trip count.
Reviewers: jfb, t.p.northover
Differential Revision: http://reviews.llvm.org/D8442
llvm-svn: 233324
The pass used to be enabled by default with CodeGenOpt::Less (-O1).
This is too aggressive, considering the pass indiscriminately merges
all globals together.
Currently, performance doesn't always improve, and, on code that uses
few globals (e.g., the odd file- or function- static), more often than
not is degraded by the optimization. Lengthy discussion can be found
on llvmdev (AArch64-focused; ARM has similar problems):
http://lists.cs.uiuc.edu/pipermail/llvmdev/2015-February/082800.html
Also, it makes tooling and debuggers less useful when dealing with
globals and data sections.
GlobalMerge needs to better identify those cases that benefit, and this
will be done separately. In the meantime, move the pass to run with
-O3 rather than -O1, on both ARM and AArch64.
llvm-svn: 233024
This change is incorrect since it converts double rounding into single rounding,
which can produce different results. Instead this optimization will be done by
modifying Clang's codegen to not produce double rounding in the first place.
This reverts commit r232954.
llvm-svn: 232962
Specifically when the conversion is done in two steps, f16 -> f32 -> f64.
For example:
%1 = tail call float @llvm.convert.from.fp16.f32(i16 %0)
%conv = fpext float %1 to double
to:
vcvtb.f64.f16
llvm-svn: 232954
If we couldn't analyze its terminator (i.e., it's an indirectbr, or some
other weirdness), we can't safely re-if-convert a predicated block,
because we can't tell whether the predicated terminator can
fallthrough (it does).
Currently, we would completely ignore the fallthrough successor. In
the added testcase, this means we used to generate:
...
@ %entry:
cmp r5, #21
ittt ne
@ %cc1f:
cmpne r7, #42
@ %cc2t:
strne.w r5, [r8]
movne pc, r10
@ %cc1t:
...
Whereas the successor of %cc1f was originally %bb1.
With the fix, we get the correct:
...
@ %entry:
cmp r5, #21
itt eq
@ %cc1t:
streq.w r5, [r11]
moveq pc, r0
@ %cc1f:
cmp r7, #42
itt ne
@ %cc2t:
strne.w r5, [r8]
movne pc, r10
@ %bb1:
...
rdar://20192768
Differential Revision: http://reviews.llvm.org/D8509
llvm-svn: 232872
The code this patch removes was there to make sure the text sections went
before the dwarf sections. That is necessary because MachO uses offsets
relative to the start of the file, so adding a section can change relaxations.
The dwarf sections were being printed at the start just to produce symbols
pointing at the start of those sections.
The underlying issue was fixed in r231898. The dwarf sections are now printed
when they are about to be used, which is after we printed the text sections.
To make sure we don't regress, the patch makes the MachO streamer assert
if CodeGen puts anything unexpected after the DWARF sections.
llvm-svn: 232842
This is very related to the bug fixed in r174431. The problem is that
SelectionDAG does not include alignment in the uniquing of loads and
stores. When an otherwise no-op DAGCombine would increase the alignment
of a load or store, the original node would be returned (with the
alignment increased), which would cause the node not to be processed by
any further DAGCombines.
I don't have a direct testcase for this that manifests on an in-tree
target, but I did see some noise in the tests for other targets and have
updated them for it.
llvm-svn: 232780
Memcpy, and other memory intrinsics, typically tries to use LDM/STM if
the source and target addresses are 4-byte aligned. In CodeGenPrepare
look for calls to memory intrinsics and, if the object is on the
stack, 4-byte align it if it's large enough that we expect that memcpy
would want to use LDM/STM to copy it.
Differential Revision: http://reviews.llvm.org/D7908
llvm-svn: 232627
COFF COMDATs (for selection kinds other than 'select any') require at
least one non-section symbol in the symbol table.
Satisfy this by morally enhancing the linkage from private to internal.
Differential Revision: http://reviews.llvm.org/D8394
llvm-svn: 232570
The input offset to needsFrameBaseReg is a negative value below the top of the
stack frame, but when converting to a positive offset from the bottom of the
stack frame this value was negated, causing the final offset to be too large
by twice the input offset's magnitude. Fix that by not negating the offset.
Patch by John Brawn
Differential Revision: http://reviews.llvm.org/D8316
llvm-svn: 232513
ARMv6K is another layer between ARMV6 and ARMV6T2. This is the LLVM
side of the changes.
ARMV6 family LLVM implementation.
+-------------------------------------+
| ARMV6 |
+----------------+--------------------+
| ARMV6M (thumb) | ARMV6K (arm,thumb) | <- From ARMV6K and ARMV6M processors
+----------------+--------------------+ have support for hint instructions
| ARMV6T2 (arm,thumb,thumb2) | (SEV/WFE/WFI/NOP/YIELD). They can
+-------------------------------------+ be either real or default to NOP.
| ARMV7 (arm,thumb,thumb2) | The two processors also use
+-------------------------------------+ different encoding for them.
Patch by Vinicius Tinti.
llvm-svn: 232468
Similar to gep (r230786) and load (r230794) changes.
Similar migration script can be used to update test cases, which
successfully migrated all of LLVM and Polly, but about 4 test cases
needed manually changes in Clang.
(this script will read the contents of stdin and massage it into stdout
- wrap it in the 'apply.sh' script shown in previous commits + xargs to
apply it over a large set of test cases)
import fileinput
import sys
import re
rep = re.compile(r"(getelementptr(?:\s+inbounds)?\s*\()((<\d*\s+x\s+)?([^@]*?)(|\s*addrspace\(\d+\))\s*\*(?(3)>)\s*)(?=$|%|@|null|undef|blockaddress|getelementptr|addrspacecast|bitcast|inttoptr|zeroinitializer|<|\[\[[a-zA-Z]|\{\{)", re.MULTILINE | re.DOTALL)
def conv(match):
line = match.group(1)
line += match.group(4)
line += ", "
line += match.group(2)
return line
line = sys.stdin.read()
off = 0
for match in re.finditer(rep, line):
sys.stdout.write(line[off:match.start()])
sys.stdout.write(conv(match))
off = match.end()
sys.stdout.write(line[off:])
llvm-svn: 232184
The main issue being fixed here is that APCS targets handling a "byval align N"
parameter with N > 4 were miscounting what objects were where on the stack,
leading to FrameLowering setting the frame pointer incorrectly and clobbering
the stack.
But byval handling had grown over many years, and had multiple layers of cruft
trying to compensate for each other and calculate padding correctly. This only
really needs to be done once, in the HandleByVal function. Elsewhere should
just do what it's told by that call.
I also stripped out unnecessary APCS/AAPCS distinctions (now that Clang emits
byvals with the correct C ABI alignment), which simplified HandleByVal.
rdar://20095672
llvm-svn: 231959
to disable lane switching if we don't actually have the instruction
set we want to switch to. Models the earlier check above the
conditional for the pass.
The testcase is one that triggered with the assert that's added
as part of the fix, use it to avoid adding a new testcase as it
highlights the same problem.
llvm-svn: 231539
This is based on the following equivalences:
select(C0 & C1, X, Y) <=> select(C0, select(C1, X, Y), Y)
select(C0 | C1, X, Y) <=> select(C0, X, select(C1, X, Y))
Many target cannot perform and/or on the CPU flags and therefore the
right side should be choosen to avoid materializign the i1 flags in an
integer register. If the target can perform this operation efficiently
we normalize to the left form.
Differential Revision: http://reviews.llvm.org/D7622
llvm-svn: 231507
This commit enables forming vector extloads for ARM.
It only does so for legal types, and when we can't fold the extension
in a wide/long form of the user instruction.
Enabling it for larger types isn't as good an idea on ARM as it is on
X86, because:
- we pretend that extloads are legal, but end up generating vld+vmov
- we have instructions like vld {dN, dM}, which can't be generated
when we "manually expand" extloads to vld+vmov.
For legal types, the combine doesn't fire that often: in the
integration tests only in a big endian testcase, where it removes a
pointless AND.
Related to rdar://19723053
Differential Revision: http://reviews.llvm.org/D7423
llvm-svn: 231396
Improve test robustness in preparation of coming commits:
- Avoid undefs which may get propagated too much.
- Remove several pointless add 0, instructions
llvm-svn: 231307
Move the specialized metadata nodes for the new debug info hierarchy
into place, finishing off PR22464. I've done bootstraps (and all that)
and I'm confident this commit is NFC as far as DWARF output is
concerned. Let me know if I'm wrong :).
The code changes are fairly mechanical:
- Bumped the "Debug Info Version".
- `DIBuilder` now creates the appropriate subclass of `MDNode`.
- Subclasses of DIDescriptor now expect to hold their "MD"
counterparts (e.g., `DIBasicType` expects `MDBasicType`).
- Deleted a ton of dead code in `AsmWriter.cpp` and `DebugInfo.cpp`
for printing comments.
- Big update to LangRef to describe the nodes in the new hierarchy.
Feel free to make it better.
Testcase changes are enormous. There's an accompanying clang commit on
its way.
If you have out-of-tree debug info testcases, I just broke your build.
- `upgrade-specialized-nodes.sh` is attached to PR22564. I used it to
update all the IR testcases.
- Unfortunately I failed to find way to script the updates to CHECK
lines, so I updated all of these by hand. This was fairly painful,
since the old CHECKs are difficult to reason about. That's one of
the benefits of the new hierarchy.
This work isn't quite finished, BTW. The `DIDescriptor` subclasses are
almost empty wrappers, but not quite: they still have loose casting
checks (see the `RETURN_FROM_RAW()` macro). Once they're completely
gutted, I'll rename the "MD" classes to "DI" and kill the wrappers. I
also expect to make a few schema changes now that it's easier to reason
about everything.
llvm-svn: 231082
TargetRegisterInfo. DebugLocEntry now holds a buffer with the raw bytes
of the pre-calculated DWARF expression.
Ought to be NFC, but it does slightly alter the output format of the
textual assembly.
This reapplies 230930 without the assertion in DebugLocEntry::finalize()
because not all Machine registers can be lowered into DWARF register
numbers and floating point constants cannot be expressed.
llvm-svn: 231023
TargetRegisterInfo. DebugLocEntry now holds a buffer with the raw bytes
of the pre-calculated DWARF expression.
Ought to be NFC, but it does slightly alter the output format of the
textual assembly.
This reapplies 230930 with a relaxed assertion in DebugLocEntry::finalize()
that allows for empty DWARF expressions for constant FP values.
llvm-svn: 230975
TargetRegisterInfo. DebugLocEntry now holds a buffer with the raw bytes
of the pre-calculated DWARF expression.
Ought to be NFC, but it does slightly alter the output format of the
textual assembly.
llvm-svn: 230930
Essentially the same as the GEP change in r230786.
A similar migration script can be used to update test cases, though a few more
test case improvements/changes were required this time around: (r229269-r229278)
import fileinput
import sys
import re
pat = re.compile(r"((?:=|:|^)\s*load (?:atomic )?(?:volatile )?(.*?))(| addrspace\(\d+\) *)\*($| *(?:%|@|null|undef|blockaddress|getelementptr|addrspacecast|bitcast|inttoptr|\[\[[a-zA-Z]|\{\{).*$)")
for line in sys.stdin:
sys.stdout.write(re.sub(pat, r"\1, \2\3*\4", line))
Reviewers: rafael, dexonsmith, grosser
Differential Revision: http://reviews.llvm.org/D7649
llvm-svn: 230794
